45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

钢纤维喷射混凝土作为面板材料的可行性研究

钢纤维混凝土作为一种新型增强材料，以其较好的受力变形特性在水利水电，交通，海岸防护，港口及军事等诸多工程中得到了广泛的应用。针对混凝土面板堆石坝面板的受力变形特点，为改善水布垭面板堆石坝面板的受力条件，提高其防渗能力，同时方便施工，现提出采用钢纤维喷射混凝土作为水布垭面板堆石坝面板材料的新构想，并通过对钢纤维喷射混凝土的物理力学特性及堆石坝面板受力变形进行分析，为钢纤维喷射混凝土在水布垭面板堆石坝面板中的实际应用提出了建议方案。     

区域防空联合预警体系探测效能分析

将联合预警体系划分为不同的子系统,按照系统集成的方法,分析和计算了区域防空条件下联合预警装备体系的探测效能;结合防空兵部队联合预警系统发展的需求,以定量的形式为联合预警体系的构建提供决策依据。     

Failure analysis used for remanufacturing of steel rolling components

The guide-pieces, used in the process line of steel rolling, were the important components. The guidepieces, which were slide contacting with the rolled-piece, had a high temperature and high speed. The wear was very serious. The results from failure analysis showed that there were three failure forms in the guide-pieces: the first was the wear during heat friction, the second was the heat fatigue under the cycle of deep heating and deep cooling, and the third was the impact rupture. Among them, the wear was the main reason. To the wear of guidepieces, there were four mechanisms, namely abrasive wear, adhesive wear, fatigue wear and corrosion wear. The failure analysis to the guide-piece laid the foundation for its remanufacturing. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China     

轻型钢骨结构低层住宅设计荷载分析

本文讨论了北美低层钢骨结构住宅结构设计的荷载问题，包括各类荷载的取值和计算方法，以及荷载组合模式，并提出了在我国相关规范没有出台前，在国内进行设计时应该注意的一些问题。     

An analog circuit design environment based on cooperating blackboard systems

A novel approach to design automation for analog circuits is presented. The prototype implementation-OASE-has been realized as a set of cooperating expert systems with blackboard architecture. The circuit specific knowledge bases use hybrid representation schemes and are strictly separated from an execution engine containing the necessary control knowledge. This alleviates the knowledge acquisition process as well as the extension and maintenance of existing knowledge. OASE has been developed as a design assistant, featuring different levels of interactivity, a hierarchical design style and fully embedded algorithmic standard tools. In its current version it is able to design a broad range of different CMOS operational amplifiers.     

温度场有限元分析的接缝单元

目前混凝土坝的仿真分析正从单坝段仿真向全坝仿真发展,因而需要采用接缝单元,笔者给出三种温度场接缝单元的计算模型：有限厚度接缝单元、近零厚度接缝单元及简化接缝单元.     

Finite‐Element Implementation of a Self‐consistent Texture Model with a Hardening Law Based on Dislocation Densities

A self‐consistent texture model is implemented in the finite‐element code ABAQUS/Explicit®. Hardening of the slip systems is described by evolution laws for dislocation densities, and the Bauschinger effect is included. With these ingredients the cold rolling of an IF‐steel is simulated and the evolution of texture and anisotropy is examined. The use of the dislocation based hardening law is found to have a significant effect on the evolution of the anisotropic yield surface, but only very little influence on the texture. Furthermore, the hardening model is used to investigate the evolution of dislocation densities in differently oriented grains during plane strain compression. It is found that the dislocation density varies greatly depending on orientation, an observation which can help to explain the orientation dependence of recrystallization.     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.