The Danish Twin Apartment Study – Part II: Mathematical modeling of the relative strength of sources of indoor air pollution

Abstract This study deals with the modeling of air pollution in apartments from laboratory measurements of source strengths, using formaldehyde and Total Volatile Organic Compounds (TVOCs) as model pollutants. The sources in two test apartments were grouped into two: building-related sources and occupant-related sources. The measured source strengths and ventilation rates were used for the prediction of concentrations expected in the apartments. These predictions were compared to measurements in the apartment over 12 months. The conclusions were that the model predictions based on emission rates measured in the laboratory can be used to predict the long-term concentration of the two model pollutants in the apartments. Considering the measured differences in ventilation between the apartments, an occupant emission rate of between 0.2 and 0.3 mg/h/kg body weight could be estimated. Based on previous suggested limits of acceptable exposures of humans to VOCs, an acceptable average emission rate of VOCs from building materials in general was estimated to be about 30 (μ/m²/h. The modeling showed that during the first 200 days, building materials dominated the emissions. After this, sources relating to the occupants dominated. On average about half of the VOC pollution originated from the building materials.     

Study on phase behavior–impact strength relationship of unsaturated polyester/polyurethane hybrid polymer network

The phase behavior of a hybrid polymer network (HPN) composed of poly[(propylene glycol maleate)-co-(propylene glycol phthalate)] crosslinked with styrene and polyester–urethane crosslinked with methylene-bis-ortho-chloroaniline was examined. The correlation between phase separation and impact strength of the HPNs is discussed. The composition of HPNs has an effect on their properties.     

纤维表面处理对植物纤维增强水泥的物理力学性能影响

植物纤维增强水泥的力学性能具有湿敏感性，随湿度增加弯曲强度下降幅度较大。本文工作采用的几种浸渍处理纤维表面的方法，有效地改善了这种状况，其中一种经处理的纤维增强水泥较没有处理的对比试样在饱水状态下的弯曲强度提高了67％，气干状态提高了18％，缩小了二者间的差距。     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

变频开关电源Fuzzy-PID控制器的设计

针对感应式变频开关电源在对金属材料进行热处理过程中，负载的等效参数和谐振频率发生变化，而变频电源的输出频率不能及时调整和跟踪的问题，结合PID和Fuzzy控制技术的优点，设计Fuzzy-PID控制器对变频电源进行控制，在大偏差时用Fuzzy控制，在小偏差时用PID调节。Fuzzy-PID控制器以单片机8098为核心，采用SPWM专用芯片SA4828，实现变频开关电源的电压、电流双闭环控制，使变频电源不仅具有较快的动态响应、更小的超调，并且具有较高的稳态精度和频率跟踪控制特性。     

The Interlaminar Bond Strength of Flexible Polymer-Metal Laminates

An alternative test method to the traditional 180° “T” peel test has been developed for the measurement of interlaminar bonding in three-ply (polyester/aluminium/polypropylene) flexible-packaging, laminate materials. The new test is thought to involve mixed mode I (opening) and mode II (shearing) failure, and takes into account the yielding of the polypropylene layer during testing. The method allows more direct comparisons between materials to be made, and allows the measurement of strong bonds, where a peel test would result in yield or fracture of the substrate arms before debonding.     

Abrasion erosion of concrete by water-borne sand

Hydraulic concrete structures frequently experience long-term abrasive erosion by water-borne sand, resulting in surface damage and eventually limiting their service life. In this study, the investigation of abrasion erosion tests on concrete with various water to cementitious material ratios (w/cm) was performed. The effects of the constituent materials on concrete structure abrasion erosion resistance were studied. The test results show that: (1) reduction in the w/cm ratio increases the tested concrete abrasion resistance; (2) the splitting tensile strength is a viable indicator for concrete abrasion resistance; (3) high permeability concrete exhibits weak abrasion resistance; and (4) concrete and low strength concrete made with coarser aggregate exhibit greater abrasion resistance.     

Preadhesion Laser Treatment of Aluminum Surfaces

An excimer laser may be used for preadhesion treatment of aluminum alloys. This method presents an alternative to the use of ecologically unfriendly chemicals involved in conventional anodizing pretreatments.

Experimental results indicate that preadhesion laser surface treatment significantly improved the shear strength of modified-epoxy bonded aluminum specimens compared with untreated and anodized substrates. The best results were obtained with laser energy of about 0.2 J/Pulse/cm² where single lap shear strength was improved by 600-700% compared with that of untreated Al alloy, and by 40% compared with chromic acid anodizing pretreatment.

The mode of failure changed from adhesive to cohesive as the number of laser pulses increased during treatment. The latter phenomenon has been correlated with morphology changes as revealed by electron microscopy, and chemical modification as indicated by Auger and infrared spectroscopy.

It can be concluded that the excimer laser has potential as a precise, clean and simple preadhesion treatment of Al alloys.     

Thermodynamic Criteria for the Maximum and Minimum Strength of Fibre-Reinforced Composite Materials

The overall performance and reliability of composite materials are, in most cases, dependent upon the behaviour of the reinforcement-matrix interface, particularly upon its ability to transfer stress.

A theory for predicting thermodynamic conditions for the maximum and zero-adhesion at the reinforcement-matrix interface is tested in this paper, based on experimental data. Proposed is a model of the relationship between mechanical properties of composite materials (tensile strength, flexural strength, Young's modulus and impact resistance) and energetic properties of matrix and reinforcement expressed by the energy ratio a = γ_l/γ₂.     

Mathematical models of the thermal decomposition of coal: 6. Effect of blend composition on coke strength

A mathematical model to predict the strength of a coke manufactured from a blend of coals is proposed. The model operates in terms of ‘bond strengths’ between the constituents. The magnitudes of these bond strengths may be determined from the strengths of cokes manufactured from the individual constituents and from a limited number of binary blends. The model has been applied to predictions of the M₁₀ index of coke strength for binary and ternary blends, and the predictions are in reasonable agreement with the experimental data. In particular, the model is able to account for the behaviour of incompatible coals and bridging coals in blends.