W型辐射管的燃烧优化以及流固耦合分析方法研究

采用Fluent软件模拟W型辐射管内部流体的燃烧状况,在不同空气过剩系数、不同燃气流量以及不同空气预热温度工况下,对辐射管内燃烧流场进行了数值模拟,得出合理可行的空气过剩系数、燃气流量和空气预热温度.在此基础上通过流固耦合分析求出辐射管的结构变形及应力分布.比较全面地对辐射管进行了分析,对类似问题具有一定的参考价值.     

包头某越冬基坑桩锚支护结构受力变形监测分析

近几年基坑支护深度H不断增加,施工周期也不断变长,在北方一些寒冷地区,一些基坑工程不得不进入越冬期.由于基坑渗水和地下水的影响,基坑土体的冬季冻胀和春季融陷容易对支护结构产生一些不良作用.针对包头某越冬基坑进行了监测,总结了桩锚支护结构在越冬时锚杆轴力变化和基坑位移变化,并提出了一些防治冻胀的措施,为类似工程提供参考.     

Non-complete relief method for measuring surface stresses in surrounding rocks

The measurement of surface stresses in surrounding rocks with the use of a relief method of annular hole-drilling was studied by numerical analysis. The stress relief process by hole-drilling was then simulated with the use of finite element method. The influences of the borehole diameter（d）, the initial stresses and the ratio of the initial principle stresses on the variations of the remained stress and the released stress in function of the relief depth（h） were discussed. The relation between the non-dimensional ratio of the released principle strains and that of the initial principle stresses, and the effect of the elastic modulus and the Poisson ratio of the rock mass on the stress relief curves were studied. The results show that the stress relief behavior formulated with the non-dimensional ratio of the released stress and the ratio of h/d is only sensitive to the ratio of the initial principle stresses and the Poisson ratio. The stresses are completely released when h equals 1.6d, and the tensile stresses take place on the bore core surface in the relief measurement process. Finally, a non-complete relief method of annular hole-drilling for measuring surface stress in surrounding rocks is proposed and the procedure is presented.     

Effects of laser heat treatment on the fracture morphologies of X80 pipeline steel welded joints by stress corrosion

The surfaces of X80 pipeline steel welded joints were processed with a CO2 laser, and the effects of laser heat treatment （LHT） on H2S stress corrosion in the National Association of Corrosion Engineers （NACE） solution were analyzed by a slow strain rate test. The fracture morphologies and chemical components of corrosive products before and after LHT were analyzed by scanning electron microscopy and energy-dispersive spectroscopy, respectively, and the mechanism of LHT on stress corrosion cracking was discussed. Results showed that the fracture for welded joints was brittle in its original state, while it was transformed to a ductile fracture after LHT. The tendencies of hydrogen-induced corrosion were reduced, and the stress corrosion sensitivity index decreased from 35.2% to 25.3%, indicating that the stress corrosion resistance of X80 pipeline steel welded joints has been improved by LHT.     

Stress analytical solution for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform distributed pressure

The stress state around circular openings,such as boreholes,shafts,and tunnels,is usually needed to be evaluated.Solutions for stresses,strains and ultimate bearing capacities of pressurized hollow cylinder are common cases.Stress analytical method for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform pressure on the outer surface and uniform radial pressure on the inner surface is given.The power series method of complex function is used.The stress analytical solution is obtained with the assumption that two layers of a cylinder are fully contacted.The distributions of normal and tangential contact stress along the interface,tangential stress on the inner boundary and stresses in the radial direction at θ=0,45 and 90,are obtained.An example indicates that,when the elastic modulus of the inner layer of a double-layered thick-walled cylinder is smaller than that of the outer layer,the tangential stress is smaller than that in the corresponding point for a traditional cylinder composed of homogeneous materials.In that way,stress concentration at the inner surface can be alleviated and the stress distribution is more uniform.This is a capable way to enhance the elastic ultimate bearing capacity of thick-walled cylinder.     

Simulation of hydrogen diffusion in welded joint of X80 pipeline steel

Hydrogen diffusion coefficients of different regions in the welded joint of X80 pipeline steel were measured using the electro-chemical permeation technique. Using ABAQUS software, hydrogen diffusion in X80 pipeline steel welded joint was studied in consideration of the inhomogeneity of the welding zone, and temperature-dependent thermo-physical and mechanical properties of the metals. A three dimensional finite element model was developed and a coupled thermo-mechanical-diffusion analysis was performed. Hydrogen concentration distribution across the welded joint was obtained. It is found that the postweld residual hydrogen exhibits a non-uniform distribution across the welded joint. A maximum equivalent stress occurs in the immediate vicinity of the weld metal. The heat affected zone has the highest hydrogen concentration level, followed by the weld zone and the base metal.Simulation results are well consistent with theoretical analysis.     

Deformation transition of intact coal induced by gas injection

Gas migration in coal bed is a multiple-physical process, of which not only includes gas desorption/diffusion through coal matrix and gas Darcy flow through the cleat system, but also results in deform...     

满堂扣件式钢管脚手架应力传递规律试验研究

满堂扣件式钢管脚手架在混凝土工程模板施工中有着广泛的应用,具有拆装方便、周转次数多、经济效益显著等诸多优点。本文通过3×3跨的满堂式扣件钢管脚手架加载实验,在施加不同荷载的情况下,研究脚手架某一立杆扣件处的应力传递规律。采用数值模拟和现场监测等分析方法,分析在不同的荷载作用下,架体内部钢管立柱的应力传递规律,其结论和研究方法可为研究类似架体的受力性能提供借鉴和参考,同时为现场关键点监控和远程安全预警系统开发提供相应的理论依据。     

腐蚀预应力钢绞线的疲劳试验分析

为了研究钢绞线腐蚀后的疲劳性能,采用通电加速腐蚀方法制作了包括5根无腐蚀与22根腐蚀预应力钢绞线试件,并通过轴向拉伸疲劳试验对预应力钢绞线腐蚀后的疲劳性能退化规律进行了研究分析,试验主要考察了腐蚀率与应力水平对钢绞线疲劳寿命的影响。试验结果表明,腐蚀后的钢绞线疲劳寿命显著降低,腐蚀钢绞线的名义应力幅与疲劳寿命在双对数坐标系下仍近似符合线性关系,同级荷载水平下的钢绞线疲劳寿命随腐蚀率的增长按指数函数衰减。此外,本文根据试验结果还建立了腐蚀钢绞线的疲劳曲面方程,并给出了不同保证率下的腐蚀钢绞线疲劳强度建议值。     

铁心电抗器气隙等效导磁面积计算

以一台实际干式带气隙铁心电抗器为例,建立电抗器的三维电磁场仿真模型,给出仿真模型内的基本假设和边界条件;采用有限元分析,计算出了不同气隙下铁心电抗器的电感值和磁路中的磁感应强度矢量图,并与部分实测数据相对比,验证了仿真模型与仿真结果的正确性.然后,以铁心电抗器的电感量为主要研究对象,定量计算在不同气隙与不同铁心直径下电抗器的电感值,给出了电感值随气隙和铁心直径的变化曲线并对其拟合及定性分析.最后,结合铁心电抗器计算公式和基本假设,推算出气隙处磁通等效导磁面积扩大系数,研究气隙等效导磁面积扩大系数随气隙和铁心直径的变化关系.所得结论可以为此类电抗器的设计计算提供一定的技术支持.