低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

NSA-500-1型氩弧焊机VD9不同接法对引弧和稳弧的影响

从一起NSA－500－1型氩弧焊机故障，分析其高压脉冲旁路二极管VD9不同接法对引弧、稳弧及设备安全的影响。     

砂基中泥浆盾构法隧道施工开挖面稳定性试验研究

 通过模型试验，对泥浆盾构施工中泥浆维持开挖面稳定的力学机理，开挖面前缘土体的应力变化规律，泥浆压力作用机理及泥皮形态进行了研究，提出了中粗砂地基中临界泥浆压力 公式。     

Inhibition of acid rock drainage from uranium ore waste using a conventional neutralization and precipitation treatment

Glass columns (length 50 cm, i.d. 4 cm) containing 900 g of uranium ore waste were subjected to a three-step process: (1) acid drainage generation, (2) neutralization and precipitation treatment and, again, (3) acid drainage generation. In the first acid generation step, lasting about one year, different variables (pyrite addition, inoculation and irrigation solution) were tested by measuring effluent pH, redox potential, total iron and sulphate. Conditions of acid generation were satisfactorily reproduced, reaching stable pH values around 2.0 that were determined mainly by pyrite addition and the type of irrigation solution used (distilled water or ferrous sulphate). The neutralization and precipitation treatment consisted of alternating irrigations of a neutralizing solution (CaO saturated plus NaOH) and a precipitating solution (ferric sulphate saturated). This treatment caused accumulation of basic iron sulphate and iron oxide precipitates according to SEM studies. After this treatment, the barrier effect created by the reaction products was checked, using irrigation solutions similar to the first step. The effluents collected showed higher pH and lower redox potential, total iron and sulphate values than those observed before the treatment, evidencing inhibition of acid drainage generation.     

对国际岩石力学委员会J_V公式的质疑

通过对国际岩石力学委员会JV 公式的论证 ,指出了该公式不符合数理逻辑。结合工程勘察实践 ,拟建了Ky新公式 ,提高了工程岩体完整程度评价方法的科学性。     

Phase behavior of ternary blends containing dimethylpolycarbonate,tetramethylpolycarbonate and poly[styrene‐co‐(methyl methacrylate)] copolymers (or polystyrene)

The miscibility and phase behavior of ternary blends containing dimethylpolycarbonate (DMPC), tetramethylpolycarbonate (TMPC) and poly[styrene‐co‐(methyl methacrylate)] copolymer (SMMA) have been explored. Ternary blends containing polystyrene (PS) instead of SMMA were also examined. Blends of DMPC with SMMA copolymers (or PS) did not form miscible blends regardless of methyl methacrylate (MMA) content in copolymers. However, DMPC blends with SMMA (or PS) blends become miscible by adding TMPC. The miscible region of ternary blends is compared with the previously determined miscibility region of binary blends having the same chemical components and compositions. The region where the ternary blends are miscible is much narrower than that of binary blends. Based on lattice fluid theory, the observed phase behavior of ternary blends was analyzed. Even though the term representing the Gibbs free energy change of mixing for certain ternary blends had a negative value, blends were immiscible. It was revealed that a negative value of the Gibbs free energy change of mixing was not a sufficient condition for miscible ternary blends because of the asymmetry in the binary interactions involved in ternary blends. Copyright © 2004 Society of Chemical Industry     

Synthesis and characterization of new thermally stable poly(ester‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic dihydroxy compounds

A series of new alternating aromatic poly(ester‐imide)s were prepared by the polycondensation of the preformed imide ring‐containing diacids, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A model compound (3) was also prepared by the reaction of 2b with phenol, its synthesis permitting an optimization of polymerization conditions. Poly(ester‐imides) were fully characterized by FTIR, UV‐vis and NMR spectroscopy. Both biphenylene‐ and binaphthylene‐based poly(ester‐imide)s exhibited excellent solubility in common organic solvents such as tetrahydrofuran, m‐cresol, pyridine and dichloromethane. However, binaphthylene‐based poly(ester‐imide)s were more soluble than those of biphenylene‐based polymers in highly polar organic solvents, including N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide and dimethyl sulfoxide. From differential scanning calorimetry thermograms, the polymers showed glass‐transition temperatures between 261 and 315 °C. Thermal behaviour of the polymers obtained was characterized by thermogravimetric analysis, and the 10 % weight loss temperatures of the poly(ester‐imide)s was in the range 449–491 °C in nitrogen. Furthermore, crystallinity of the polymers was estimated by means of wide‐angle X‐ray diffraction. The resultant poly(ester‐imide)s exhibited nearly an amorphous nature, except poly(ester‐imide)s derived from hydroquinone and 4,4′‐dihydroxybiphenyl. In general, polymers containing binaphthyl units showed higher thermal stability but lower crystallinity than polymers containing biphenyl units. Copyright © 2005 Society of Chemical Industry     

Stability of Equilibria in a Four-dimensional Nonlinear Model of a Hydraulic Servomechanism

Starting from plysical laws a four-dimensional nonlinear model for mecano-hydraulic servomechanisms is deduced. The stability of its equilibria is analysed using a theorem of Lyapunov and Malkin to handle the critical case due to the presence of zero in the spectrum of the matrix of the linear part around equilibria. Stability diagrams are drawn and simulation results are presented through phase diagrams.     

过氧化甲乙酮合成研究

论述了过氧化甲乙酮的合成方法，用阳离子交换树脂催化剂代替传统的无机酸催化剂。考察了离子交换树脂用量、反应温度对反应产率、活性氧含量的影响及溶剂对产品稳定性的影响。     

Passivity‐based sliding mode control for nonlinear systems

Passivity with sliding mode control for a class of nonlinear systems with and without unknown parameters is considered in this paper. In fact, a method for deriving a nonlinear system with external disturbances to a passive system is considered. Then a passive sliding mode control is designed corresponding to a given storage function. The passivity property guarantees the system stability while sliding mode control techniques assures the robustness of the proposed controller. When the system includes unknown parameters, an appropriate updated law is obtained so that the new transformed system is passive. The passivation property of linear systems with sliding mode is also analysed. The linear and nonlinear theories are applied to a simple pendulum model and the gravity‐flow/pipeline system, respectively. Copyright © 2008 John Wiley & Sons, Ltd.