80年代黄河中游来沙减少的原因分析

80年代黄河中游来沙量减少,主要原因是降雨量减少和降雨强度减小,流域综合治理也起到了减沙作用。据分析,降雨因素减沙约占总减沙量的70％,流域综合治理减沙约占30％。     

应用计算机实现选矿自动化

本文就太钢尖山铁矿计算机控制系统的硬件构成，顺控系统的软件编制、模拟调试以及现场调试等方面展开论述。     

GaAs器件工艺中等离子刻蚀及计算机辅助监控技术研究

用Ｎ２气和ＮＦ３反应气体，在较低的刻蚀功率下实现了用薄正性光刻胶ＡＺ１５１８作掩模，均匀、快速刻蚀ＳｉＯ２，ＳｉＯＮ，Ｓｉ３Ｎ４，ＷＮ，Ｗ等材料的等离子刻蚀技术。利用到蚀过程中射频参数的变化和计算机技术，将射频参数的变化在计算机屏幕上实时显示，实现了计算机辅助监控和终点检测技术。     

镍代钴矿用硬质合金的新进展

概述了镍代钴矿用硬质合金的国内外进展情况．     

电解法烟道气二氧化硫在线监测系统的设计

介绍了一种烟道气中SO2在线检测系统，该系统可以实现24h不间断地监测烟道气中SO2的体积分数和质量浓度，同时将信息经网络传送给环保有关部门，具有一定的新颖性、可靠性、准确性。     

Rhizobium trifolii capsular polysaccharide: a novel biopolymer with striking physical properties

The physical properties of the capsular polysaccharide of Rhizobium Trifolii (CPS) were investigated. Viscosity measurements provided information about the hydrodynamic volume of single coils, the perturbation of solvent flow and the shear-thinning behaviour of concentrated solutions. Changes in chain geometry and the development of an intermolecular network as a function of temperature were monitored using the techniques of optical rotation and dynamic oscillation. Finally, analysis of calorimetric thermograms elucidated the type of interactions between CPS and the bacterial levan. Overall, the Rhizobium polysaccharide was found to form thermally-reversible gels at an extremely low 'minimum critical gelling concentration' (c_o∼ 0.35gl^-1). At temperatures above the gel melting point (∼ 48°C), however, the compact polymer coils entangled at comparatively high concentrations (about 60 times higher than c_o). In the presence of a highly branched levan, the thermal stability of ordered CPS structures increased as a consequence of thermodynamic incompatibility between the two polymers.     

Resilient metal spring network silicone-matrix composite for separable interconnections

Resilient metal spring silicone-matrix conducting composites for separable interconnections in electronics were fabricated by the impregnation of silicone into a preform comprising randomly oriented C-shaped Cu-Be springs and a small proportion of Sn-Pb solder, which served to connect the springs at some of their intersections. Composites containing 6.1-9.8 vol.% total filler exhibited volume electrical resistivity 0.5-1.0 mΩ.cm and contact resistivity (with copper) 11-17 mΩ.cm². A compressive stress of about 30 kPa was needed for the low contact resistivity to be reached. The volume 17-26% and the contact resistivity increased by 5% after heating in air at 130-150°C for seven days. Composites containing <9 vol.% total filler showed no stress relaxation for seven days at 6.0% strain.     

转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。     

Influence of Coherent Flow Structures on the Dynamics of Suspended Sediment Transport in Open-Channel Flow

The influence of suspended sediments on coherent flow structures has been studied by simultaneously measuring the longitudinal and vertical components of the instantaneous velocity vector and the instantaneous suspended particle concentration with an acoustic particle flux profiler. The measurements were carried out in clear water and in particle-laden open-channel flows. In both cases, they clearly show the predominance of ejection and sweep phases that are part of a burst cycle. The analysis further demonstrates the importance of the ejection and sweep phases in sediment resuspension and transport. Ejections pick up the sediment at the bed and carry it up through the water column close to the surface. It is shown that ejections and sweeps are in near equality in the near-bottom layer, whereas ejections clearly dominate in the remaining water column. The implications of these results for sediment transport dynamics are discussed.     

Procedure for Measuring Low Concentrations of H2 and H2S Above a Water Surface

A simple measuring procedure for low concentrations of H₂ and H₂S (at the level of ppm fractions) above the surface of water by using sensitive gas analyzers is suggested. The procedure is easily accomplished in conditions outside the laboratory (under field conditions).