阳泉市煤矿采空区地质因素对公路的破坏

介绍了阳泉市煤矿采空区对公路建设所造成的危害，对其上覆岩层变形破坏的地质因素及其破坏机理作了分析，指出应该采取各种措施减少对公路的破坏。     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

三峡工地高压供电线路故障判断方法的探讨

高压供电设备故障特别是输电线路的高压接地故障对工地的影响是相当大的。由于接地故障为隐性故障，没有明显的物理现象，且若是长期接地可能会发展成较为严重的两相或三相短路故障，使系统解列运行直至崩溃；由于工地流动人员较多，还易造成电击事故。利用高压一相接地时在线路中产生零序电压这一特性来迅速判断和切除接地的用电设备，可以保证各项施工的顺利进行。     

Bruchanalyse an Hohlgläsern

Failure analysis of hollow glasses The failure analysis is very important to clarify damages of hollow glasses. Damages of glass bottle through over pressure are very often linked with damages to persons. This is the reason why the causal research is from particular importance. Different surface characteristics of glass fragments as well as the fracture pattern give hints to the direction of the crack, the stress just before breakage and the reason of stress. A reconstruction of the bottle is a further helpful instrument for cause studies. The difference of the various characteristics of the surface will be explained. Further on there will be discussed different reasons and mechanism of fracture.     

矿井串联系统模糊可靠性理论的研究

矿井系统不仅具有随机性，而且同时也具有模糊性，在系统分析与设计过程中应同时考虑这两种不确定性因素的影响。文中提出了模糊故障、模糊功能、系统模糊运营状态和广义可靠度等概念，并在此基础上提出了求单元及串联系统的生产能力、营运费用、应急维修费用、修理时间和广义可靠度等指标的方法，建立了使系统平均生产能力最大的系统最优运营策略的数学模型。     

GaAs FET辐射退化研究

低噪声ＧａＡｓ ＦＥＴ和功率ＧａＡｓ ＦＥＴ经中子辐射都未发生致命性的通或断失效，直流偏置伏态下，其失效模式仅仅表现为源漏饱和电流ＩＤＳＳ的退化降低，据此提出了ＩＤＳＳ退化失效与快中子注量φｎ之间的解析关键式ｌｎｙ＝ａ＋ｂｌｎφ。     

Failure analysis and wear mechanism study of a heavily loaded gear

Failure analysis and a study of the wear mechanism were performed on a heavily loaded carburized gear with some unusual features. The analysis showed that the different failure forms on the tooth surface of the gear were dependent on the sub-surface shearing stress, the lubrication conditions and the surface roughness. Delaminations formed on the addendum surface were the main reason for the gear failure. A suggestion for improvement has been tried, and a desirable result has been obtained.     

堆底熔穿事故的场外后果及其对策

在压水堆核电站应急计划和应急响应中，堆底熔穿事故占有重要位置。本文用法国核电厂事故源项Ｓ３（对应于堆底熔穿事故）计算了在典型气象条件下的场外放射学的后果，根据一般防护决策原则和我国颁布的干预水平，提出了保护公众的应急防护措施的建议。     

采用表面粘涂技术提高设备的抗腐蚀性能

通过表面粘涂，对受到腐蚀、冲蚀、气蚀的设备进行表面修补与防护，可提高设备的使用寿命。