Evaluation of bismuth doped La2-xBixNiO4+δ (x = 0, 0.02 and 0.04) as cathode materials for solid oxide fuel cells

Bismuth doped La_2-xBi_xNiO_4+δ (x = 0, 0.02 and 0.04) oxides are investigated as SOFC cathodes. The effects of Bi doping on the phase structure, thermal expansion, electrical conduction behavior as well as electrochemical performance are studied. All the samples exist as a tetragonal Ruddlesden-Popper structure. Bi-doped LBNO-0.02 and LBNO-0.04 have good chemical and thermal compatibility with LSGM electrolyte. The average TEC over 20–900°С was 13.4 × 10^?6 and 14.2 × 10^?6 K^?1 for LBNO-0.02 and LBNO-0.04, respectively. The electrical conductivity was decreasing with the rise of Bi doping content. EIS measurement indicates Bi doping can decrease the ASR values. At 750 °C, the obtained ASR for LBNO-0.04 is 0.18 Ωcm², which is 56% lower than that of the sample without Bi doping, suggesting Bi doping is beneficial to the electrochemical catalytic activity of LBNO cathodes.     

Simulation Analysis of the Heat Transfer Performance of an N-type Microchannel Heat Exchanger

A microchannel heat exchanger with a triangular wave and symmetrical triangular wave structure was proposed in this paper. In addition, a new N-type microchannel heat exchanger was developed to balance the heat transfer performance and pressure drop. The relationship between different configurations of the N structure of the microchannel and the heat transfer performance was analyzed. The results showed that, at a high inlet flow rate, the symmetrical triangular wave microchannel had the best heat transfer performance, followed by the triangular wave microchannel and the straight channel. At the same flow rate, the degree of disturbance of the fluid was highest in the symmetrical N-structure microchannel, and an excellent heat transfer effect was observed.     

Lecture capture with real‐time rearrangement of visual elements: impact on student performance

The primary goal of this study is to create and test a lecture‐capture system that can rearrange visual elements while recording is still taking place, in such a way that student performance can be positively influenced. The system we have devised is capable of integrating and rearranging multimedia sources, including learning content, the instructor and students' images, into lecture videos that are embedded in a website for students to review after school. The present study employed a two‐group experimental design, with 153 participants (145 females and 8 males) making up an experimental group in which lecture courses were recorded using the new lecture‐capture system, and 149 participants (140 females and 9 males) forming a control group whose lectures were recorded by traditional means. All participants were in the freshman college and studying Introduction to Computer and Information Science in one of six classes, and were randomly assigned to one of the two groups. The participants' midterm examination and final examination scores were collected as indicators of their academic performance, with their mathematics entrance scores used as a pre‐test. The findings obtained from analysis of covariance (ANCOVA) suggest that appropriate rearrangement of visual elements in lecture videos can significantly impact students' learning performance.     

Assessment of spray quality from an external mix nozzle and its impact on SQL grinding performance

Spray quality is the critical factor which decides the efficacy of Small Quantity Lubrication (SQL) technology in a high specific energy involved machining process like grinding. Yet, the understanding about spray quality, the actual process mechanics and its effect on machining performance is inadequate. The present work is an attempt to establish a correlation between the spray input variables, quality of the spray and machining performance of SQL grinding through modelling and experiments. Using computational fluid dynamic techniques, the variation of droplet size, droplet velocity, number of droplets and heat transfer coefficient have been analysed at different input parameters and the computed trends have been verified and validated. CFD modelling of spray indicates that it is possible to produce aerosol medium with high heat dissipation ability at moderately high air pressure and low flow rate. It also shows that any increase in atomising air pressure favourably leads to notable increase in wetting area and also results in substantial enhancement in heat dissipation ability. Reduction of residual stress is thus remarkably good. On the other hand, grinding fluid flow rate, if increased, offers significantly better lubricity and reduces the grinding force which also reduces tensile residual stress. Short spell grinding test results are found to be in good agreement with CFD results.     

Geopolymer concrete-filled pultruded composite beams – Concrete mix design and application

The limited research on the geopolymer concrete mix design for targeting a specific strength is identified an obstacle for their effective design and wide use. In this paper, a mix design procedure has been proposed for fly-ash based geopolymer concrete and its use as infill hybrid composite beam is investigated. Then, the structural performance of geopolymer concrete filled hybrid composite beam is investigated to determine their possible application in civil infrastructure. Firstly, a detailed procedure of mix design for fly-ash based geopolymer concrete is presented. Secondly, three hybrid beams filled with geopolymer concrete were prepared and tested in a four-point bending setup to evaluate their flexural modulus and modulus of rupture. Numerical and analytical evaluation of the behaviour of hybrid beam were performed and results showed a good agreement with the experimental investigation. Thirdly, the suitability of the beam for a composite railway sleeper is evaluated and compared with existing timber and composite sleepers. Finally, the beams’ performance in a ballast railway track is analysed using Strand7 finite element simulation software and the results showed that the new concept of using geopolymer concrete as infill to pultruded composite section satisfied the stiffness and strength requirements for a railway sleeper.     

Effect of in-app components,medium, and screen size of electronic textbooks on reading performance,behavior, and perception

Although many app-based textbooks are available for students, reading have not been thoroughly outlined. This study aimed to understand how changes from paper to electronic textbooks have affected the academic reading task, investigate student users’ perceptions of in-app components and screen sizes, and identify issues affecting in-app components and task requirements. A mixed factorial design experiment was employed. Results showed that there were no significant changes in comprehension and time spent reading between print text and the iPad. Yet, student highlighting, notetaking, and reading behavior and perception significantly changed based on condition. In addition, students struggled to use in-app components and found them frustrating especially when accounting for sentence splitting. The findings presented can assist in understanding the changes in student reading behavior, which can be used to improve interface design of future e-textbooks.     

超高效液相色谱串联质谱法测定烟草中的噁霉灵残留

为降低烟草中噁霉灵检测中的基质干扰，提高检测灵敏度和和稳定性，通过试验建立了以QuEChERS为样品前处理方法、液相色谱串联质谱仪为检测仪器的烟草中噁霉灵残留检测方法。样品加水浸润后，经丙酮提取、盐析试剂包除水、石墨化炭黑除杂后，采用Agilent ZORBAX 300SB-C8液相色谱柱（2.1 mm×100 mm，1.8 μm）分离，甲醇-水程序洗脱，ESI雾化，串联质谱MRM检测。结果发现，该方法在0.0025~0.0500 mg/L范围内线性良好，决定系数r²=0.9996，定量检测限1.06 μg/L，回收率在90.8%~92.0%之间，相对标准偏差为5.1%。运用该方法测定烟草中的噁霉灵，操作简单，检测精度高，满足CORESTA对烟草农残检测的要求。     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Systematic convergence of nonlinear stochastic estimators on the Special Orthogonal Group SO(3)

This paper introduces two novel nonlinear stochastic attitude estimators developed on the Special Orthogonal Group with the tracking error of the normalized Euclidean distance meeting predefined transient and steady‐state characteristics. The tracking error is confined to initially start within a predetermined large set such that the transient performance is guaranteed to obey dynamically reducing boundaries and decrease smoothly and asymptotically to the origin in probability from almost any initial condition. The proposed estimators produce accurate attitude estimates with remarkable convergence properties using measurements obtained from low‐cost inertial measurement units. The estimators proposed in continuous form are complemented by their discrete versions for the implementation purposes. The simulation results illustrate the effectiveness and robustness of the proposed estimators against uncertain measurements and large initialization error, whether in continuous or discrete form.