复合形法优化内河航道重力式护岸

采用复合形优化法,结合《港口及航道护岸工程设计与施工规范》中推荐的抗滑、抗倾稳定的分项系数计算方法,并考虑了内河航道船形波等作用的影响效应,对重力式护岸断面进行了优化。     

Reduced modified quadratures for quadratic membrane finite elements

Reduced integration is frequently used in evaluating the element stiffness matrix of quadratically interpolated finite elements. Typical examples are the serendipity (Q8) and Lagrangian (Q9) membrane finite elements, for which a reduced 2 × 2 Gauss–Legendre integration rule is frequently used, as opposed to full 3 × 3 Gauss–Legendre integration. This ‘softens’ these element, thereby increasing accuracy, albeit at the introduction of spurious zero energy modes on the element level. This is in general not considered problematic for the ‘hourglass’ mode common to Q8 and Q9 elements, since this spurious mode is non‐communicable. The remaining two zero energy modes occurring in the Q9 element are indeed communicable. However, in topology optimization for instance, conditions may arise where the non‐communicable spurious mode associated with the elements becomes activated. To effectively suppress these modes altogether in elements employing quadratic interpolation fields, two modified quadratures are employed herein. For the Q8 and Q9 membrane elements, the respective rules are a five and an eight point rule. As compared to fully integrated elements, the new rules enhance element accuracy due to the introduction of soft, higher‐order deformation modes. A number of standard test problems reveal that element accuracy remains comparable to that of the under‐integrated counterparts. Copyright © 2004 John Wiley & Sons, Ltd.     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

关于重力坝坝内细部构造设计的几个问题

重力坝常采用横，纵缝将坝体分为柱状体施工。为此，横缝须设置止水，纵缝则待坝体冷却后灌浆，将柱状坝块连成整体。此外坝体内部还须设置坝面排水管以消除坝内渗透压力。关于坝内这些细部构造，设计规范仅有原则性要求，一般专业书列举不多，目前有些工程往往参照已建工程的设计图采用，常由于施工详图不祥易发生施工质量问题。根据丹江口重力坝设计经验，对接缝灌浆中的键槽，止浆片，灌浆管道，出浆盒，排气槽及排气管，基岩陡坡     

应用图论及广义简约梯度法进行压力管网优化设计

广义简约梯度法(GRG)是非线性规划算法中最有效的算法之一，本文把图论应用于广义简约梯度法优化的过程中，使输入简便，计算简化，应用GRG算法对武汉市的汉阳管网进行了模拟优化设计，并对管段的计算管径用线性规划法进行标准化，取得了满意的结果     

东方红浆砌石重力坝扬压力安全评价

东方红水库大坝是一座运行近40a的浆砌石重力坝，坝体裂缝、坝体渗漏及坝体碳化严重，扬压力有逐年增高的趋势。本文利用坝基扬压力测压管水位观测资料建立了测压管水位的统计模型，并结合现场渗漏实测流量资料建立了渗流反分析模型，详细分析了坝基的渗流性态和扬压力状态，并对其渗流性态做出安全评价。     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

龙开口水电站溢流坝段动力模型破坏试验研究

采用仿真混凝土材料研究了龙开口水电站溢流坝段在不同因素影响下的动力破坏特征,并通过对6个模型试验结果的分析探讨了溢流坝段的动力破坏机理。试验中考虑了坝体-库水的动力相互作用以及横河向地震动对大坝破坏的影响,采用规范谱波和场地谱波两种地震动激励进行模型超载破坏分析。试验结果为工程设计和评价溢流坝段的抗震性能提供依据。     

An automatic method for controlling the centre of gravity of a model

In many applications the location of the centre of gravity of a mechanical part is an important factor that a designer must consider. If it is not in a desired location, a part might not work properly, e.g. unbalanced force might be generated in a rotational part. After a part is modeled, its centre of gravity cannot be altered unless its external shape or internal mass distribution is changed. However, the external shape is usually constrained by other design considerations. In this paper, an algorithm is proposed for controlling the centre of gravity of a hollowed part. Using this algorithm, the location of the centre of gravity of a part is controlled by changing its internal mass distribution.     

Effect of Reactor Ambient Pressure on the Morphology of Spray Dried Magnesium Sulphate Powders

The effect of reducing the reactor air pressure on the morphology of spray dried magnesium sulphate powders is investigated, experimentally. A reactor, capable of drying and pyrolyzing solution sprays at low pressures, is designed and manufactured. A vibrating mesh nebulizer is employed to generate the spray. Four different pressures, starting from 60 Torr to the atmospheric pressure, and two different reactor air temperatures of 130°C and 420°C, are considered. In addition, two different concentrations of magnesium sulphate solutions are tested. The results are explained based on the effect of reactor air pressure on the droplet evaporation rate.