A PV installation framework concerning electricity variable rates

This paper assesses building integrated photovoltaic (BIPV) installation parameters based on the profit generated by a photovoltaic system. It takes into consideration a home building case study and it investigates its monthly energy demand based on a specific location and a typical occupancy. The capability of a photovoltaic (PV) system to generate more profit occurs when solar intensity is maximum while the electric energy price is at its highest rate. The paper traces a framework that encompasses different aspects such as energy demand, energy price, and solar intensity. This framework identifies profit alternatives according to different installation parameters. A tool that predicts a PV installation hourly electric energy production is developed. The profit generated is simulated for home buildings located in Beirut (Lebanon) and Xihua (China), both at 33.8° latitude north. The paper highlights a new approach for BIPV installations, taking into account weather conditions, energy demand, and electric energy utility rates.     

Electrochemical growth and characterization of iron doped cadmium sulfide thin films

Cadmium Sulfide and Ferrous doped Cadmium Sulfide thin films have been prepared on different substrates using an electrodeposition technique. Linear sweep voltammetric analysis has been carried out to determine deposition potential of the prepared films. X-ray diffraction analysis showed that the prepared films possess polycrystalline nature with hexagonal structure. Surface morphology and film composition have been analyzed using Scanning electron microscopy and Energy dispersive analysis by X-rays. Optical absorption analysis showed that the prepared films are found to exhibit Band gap value in the range between 2.3, 2.8 eV for Cadmium Sulfide and Ferrous doped Cadmium Sulfide.     

利用高频结构仿真器分析波导魔T

高频结构仿真器（HFSS）是一种微波器件设计软件，该软件界面友好，通过仿真计算减小了调试工作量，使得微波器件的设计变得简单易行。本文利用HFSS对波导魔T进行了仿真分析，得到了该器件的S参数和动、静态场的分布情况，并对该器件进行了优化设计。     

Measurement and Identification of the Parameters of SPICE-Models of a Bipolar Transistor

A method of measuring and identifying the static parameters of a bipolar transistor is considered. The characteristic of the transistor, from which the parameters of the model are determined, is chosen depending on what group the calculated parameters belong to. The characteristics are measured in such a way that the equations of the model describing them can be reduced to the simplest form.     

基于模式理论光栅椭偏参数反演的数值模拟

将一种广泛用于求解系统优化问题的方法——正单纯形法，求解光栅的椭偏方程。首先，利用求解光栅的傅立叶模式理论对TE和TM波的复反射系数进行求解。然后计算出其相应的椭偏参数(△，Ψ)，并在该值的基础上加入不同偏差的随机高斯噪声，将加入噪声后的值(△m，Ψm)作为模拟测量值。最后使用优化算法进行反演。通过对几种常用面形光栅椭偏参数的数值模拟，一方面表明傅立叶模式理论计算光栅的椭偏参数不仅精度高。而且速度快；另一方面表明利用正单纯形法得到的光栅参数值很接近于正演时假设的参数值，从而从理论上证明了利用椭偏法测量光栅各种光学参数的可行性。     

露天多段深孔微差爆破孔网参数优化设计

本文对露天多段深扎微差爆破孔网参数进行了优化，使每排炮扎成直线排列，两排之间成交替正三角形排列，优化设计后，爆破作用比较均匀，大块率下降了56％，同时，爆破根底产生的机会和程度也大大下降。     

井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

钻井参数仪的模块化设计方法研究

文章以模块化设计原理为基础，讨论了钻井参数仪的模块划分，模块化设计准则和主要设计内容。采用模块化设计方法、现场设备网络的开放网络和现场总线解决方案设计的钻井参数仪，具有传输信号稳定、可靠性高、抑制噪声能力强、组建现场网络成本低等特点。     

带参数的一阶脉冲微分方程边值问题

利用上下解和单调迭代法。讨论了带参数的一阶脉冲微分方程。获得了单边Lipschitz条件下这类方程边值问题的解的存在性。     

Texture Changes During the Ripening of Port Salut Argentino Cheese in 2 Sampling Zones

ABSTRACT: Texture changes during ripening of Port Salut Argentino cheese for different sampling zones were studied. Compression relaxation tests were performed and results were analyzed using both Maxwellian and Peleg's models. Elastic equilibrium modulus obtained from the Maxwellian model decreased from 1.22 to 0.11 10⁴Pa during ripening. The constants derived from Peleg's model, k₁ and k₂, diminished with ripening time from 1.18 to 0.71 min and from 1.27 to 1.12, respectively. Asymptotic equilibrium modulus from Peleg's model decreased from 0.95 to 0.07 10⁴Pa during ripening. Rate parameters derived from a 1st order kinetics applied to both equilibrium moduli showed that the decrease was faster in the external zone (0.0846 d⁻¹) than in the central zone (0.0368 d⁻¹). The correlation between equilibrium moduli, salt concentration, moisture content, and maturation indexes was obtained with a determination coefficient of 0.76.