基于LonWorks和DSPs的智能节点

本文提出了一种基于LonWorks和DSPs的智能节点设计方案，并给出了具体的实现方法。该方案简单、可靠，充分利用了LonWorks强大的网络性、可靠性和DSPs强大的数据处理能力，大大提升了节点的智能化程度。     

山前平原地下水侧向补给潜力空间变异模拟

SWAT模型利用分辨率较高的DEM数据,可以估算山前地下水侧向补给的空间变异,并可以计算不同降水年型下补给量的差别。模拟需要对研究区进行填洼、流向确定、汇流和河网水系的提取四步运算,并对河道临界支撑面积的取值进行分析。分别模拟了平水年和丰水年两种降雨年型下研究区13个出水口的地下水侧向补给潜力。在研究区,由于地形的变化,导致山与平原交接断面上出水口的集水面积变异非常大,因此山前平原所接受的地下水侧向补给量的空间变异也非常大。不同的降雨年型下,降雨量转化为地下水侧向补给量的比例也不同。平水年的转化比例较小,丰水年的转化比例较大。应用SWAT模型时,与ArcView的拓展模块有机结合,可以更方便提取完整的大流域,划分出合理的子流域。     

矿山抗采动农村楼房的试验研究

本文通过两栋不同加固方案的二层农村楼房抗采动现场试验结果的分析,对不同加固措施的作用机理、效果及其设置条件进行了研究探讨,并提出,在农村采动区兴建抗采动变形楼房,是解放村庄下压煤、节约耕地和降低加固费用的途径。     

Kinetic investigation of the carbothermal reduction of an Iranian clay

The kinetics of the carbothermal reduction of clay under argon atmosphere has been investigated by the X-ray diffraction method. The clay-carbon (excess) mixture was formed into 2 cm diameter disks of different thicknesses. Experimental data evidences the significant effect of sample thickness on the reaction rate at 1400 °C. Decreasing thickness promotes mullite dissociation and formation of SiC and alumina powders. Mathematical modeling of the reaction system showed the gas diffusion in the Knudsen regime through the pellet to be the rate controlling step. Diffusivity of CO and reacted core tortuosity factor have been calculated.     

X-ray structure analysis and elastic properties of a fabric reinforced carbon/carbon composite

The effect of heat treatment on microstructure of a plain-weave carbon fabric reinforced carbon-carbon composite with phenolformaldehyde-derived carbon matrix was investigated by X-ray diffraction. The diffraction patterns were analysed by the least-square fitting program Carbonxs. After heat treatment from 1000 to 2800 °C the interplanar distance of (002) planes decreased from 3.488 to 3.420 Å and the lattice parameter in basal plane increased from 2.440 to 2.464 Å, respectively. Simultaneously, the coherent block size in the basal plane directions increased from 18 to 54 Å, which was accompanied by an increase of the fraction of organised carbon atoms from 0.50 to 0.85. The 002 diffraction profile of the composite was much narrower than the sum of peaks of the matrix and fabric alone. This can probably be caused by a better crystallographic ordering (or by a partial graphitisation) of the matrix in the composite. On the other hand, the composite Young’s modulus slightly decreased with the treatment temperature increasing from 2200 to 2800 °C in spite of the established strong improvement of fibre crystallinity and, therefore, fibre modulus. The mechanisms diminishing the modulus of composite (e.g. partial matrix graphitisation at the fibre/matrix interface and decreasing fibre/matrix contact area) probably prevailed over the increasing contribution of the fibre modulus.     

A3钢的工业大气腐蚀

在辽宁省工业城市进行 A3钢大气暴露试验。两年后测出不同地点腐蚀率。依据所记录的各试验点的气象数据和污染数据,讨论了 A3钢的大气腐蚀规律。     

Possible tactics to improve the growth of single-walled carbon nanotubes by chemical vapor deposition

The growth time, growth mode and the method of preparing the supported catalysts play an important role in the growth of single-walled nanotubes (SWNTs). Their effects on the chemical vapor deposition (CVD) growth of SWNTs with MgO-supported catalysts were investigated in this study. It is shown that the growth rate of SWNTs was large during the initial few minutes of growth, however the quality of the tubes was low owing to the formation of many defects. Long term growth may favor the formation of tubes with high quality and high yield, but the introduction of other forms of carbon (impurities) is also unavoidable. There was a balance between the increase in yield and quality and sacrifice of the purity during growth of SWNTs. MgO-supported catalysts prepared by the co-precipitation method were found to be more effective for the synthesis of SWNTs than those prepared by the widely used impregnation method. The size and dispersion state of the catalyst were found to be crucial in enhancing the growth of SWNTs. In addition, growth on the surface of SWNTs over nanosized catalyst films was shown to be more favorable for the synthesis of tube products with higher quality, yield and purity.     

Irradiation Defects in Silicon Crystal

The application of irradiation in silicon crystal is introduced.The defects caused by irradiation are reviewed and some major ways of studying defects in irradiated silicon are summarized.Furthermore the problems in the investigation of irradiated silicon are discussed as well as its properties.     

Dynamic response of a Mindlin elastic rectangular plate under a distributed moving mass

The elastodynamic response of a rectangular Mindlin plate subjected to a distributed moving mass is investigated. The set of governing characteristic partial differential equations that include the effects of shear deformation and rotary inertia is expressed in its dimensionless form. A finite difference algorithm is employed to transform the differential equations into a set of linear algebraic equations. Simply supported edge conditions were used as an illustrative example. The analysis is also valid for other edge conditions. It is found that the maximum shearing forces, bending and twisting moments occur almost the same time. Also, the values of the maximum deflections are higher for Mindlin plates than for non-Mindlin plates.     

Microstructural changes accompanying repair welding in 5xxx aluminium alloys and their effect on the mechanical properties

At the shipyards, the aluminium alloy 5083 is welded with a multi-pass sequence using the metal inert gas technique. If, while checking the weld integrity either after welding or during service, defects are detected in the vicinity of the weldment, repairs are usually employed to extend the service life.

The repair method involves removal of the upper passes, depending on the thickness and re-welding under the same conditions.

Purpose of this paper is to examine the microstructural changes accompanying repair welding, define their effect on properties of primary importance and set, if possible, an upper limit as far as the number of repairs is concerned.