ADS熔盐散裂靶中子学性能研究

与传统加速器驱动次临界系统（ADS）采用金属靶作为散裂中子靶的设计不同,加速器驱动次临界熔盐堆（AD-MSRs）采用靶堆一体的设计,直接使用燃料熔盐作为散裂中子靶。由于熔盐靶的中子学性能直接影响AD MSRs的能量放大系数、核废物的嬗变和核燃料增殖的效率,所以本研究基于MCNPX程序,详细计算了高能质子轰击氟盐和氯盐两种熔盐靶产生的散裂中子产额、散裂中子能谱、能量沉积分布以及散裂产物等中子学性能,并与液态Pb和铅铋共熔体（LBE）两种液态金属靶进行了对比。计算结果表明,熔盐靶在散裂中子产额上与液态金属靶有一定的差距,但熔盐靶内能量沉积分布的梯度较小,更有利于靶区的热量导出。与液态Pb和LBE靶相比,熔盐靶的散裂产物中包含更多的气体以及高质量数的α发射体核素。     

铝合金电磁铸造工艺参数的研究

通过近似计算和试验确定了工程规模的铝合金电磁铸造（ＥＭＣ）基本工艺参数如感应器电流、电压、频率、功能消耗等一液柱高度及稳定性的关系，设计制造了ＥＭＣ装置，成功地铸造了截面直径为０．１８ｍ，０．１１×０．０５ｍ，０．５２×０．１３ｍ的铝及铝合金锭和扁锭。     

用熔盐电解法制备超细钨粉

在NaCl-KCl-Na2WO4-WO3熔体中,用熔盐电解法电解氧化钨制取细钨粉和超细钨粉。在电解温度为720℃,阴极电流密度为250mA/cm^2的条件下,得到平均等积圆直径为1．2μm、长宽比为1．6的超细钨粉。在低阴极电流密度时,阴极的电解反应为W^6 放电,在高阴极电流密度时,阴极的电解反应为Na^ 放电。研究了温度、阴极电流密度和Na2WO4的含量对电流效率的影响。     

金属钛粉的制备工艺

钛粉作为钛粉末冶金的主要原料,其品质及生产成本限制了钛及钛合金粉末冶金的发展.综述了机械合金化法、氢化脱氢法(HDH)、雾化法、金属热还原法、熔盐电解法制备钛粉的基本原理和工艺现状.新兴的生产技术有望降低钛粉生产成本,从而推动钛及钛合金粉末冶金的发展,扩大其应用范围.     

Thermal Conductivity of Molten Lead-Free Solders

The paper reports measurements of the thermal conductivity of a number of molten solders for the electronics industry that are part of a group of materials designed to be free of the toxic problems associated with lead-based solders. The measurements have been carried out with a transient hot-wire instrument originally designed for the measurement of the thermal conductivity of pure molten metals. In the application reported here the instrument has been used largely unchanged but an improved finite-element code has been used for the analysis of the raw data so as to yield the thermal conductivity of the molten solders. The measurements extend from the melting point of the solder up to 625 K. The uncertainty in the thermal conductivity measurements is estimated to be no larger than 3%.Paper presented at the Seventh Asian Thermophysical Properties Conference, August 23–28, 2004, Hefei and Huangshan, Anhui, P. R. China     

金属熔体电磁成形过程研究

以制备无污染的航空发动机叶片为背景 ,分析了金属熔体电磁成形定向凝固技术的原理 ,并以铝合金及 1Cr1 8Ni9Ti为研究材料 ,探讨了交流电磁场作用下金属熔体的感应加热熔化及约束成形过程 ,结果表明 :感应器结构决定其内部的磁场及电磁压力分布 ,感应器输入功率、熔体高度、上下液固界面位置、抽拉速度及冷却条件等参数综合影响金属加热熔化特性、熔体形状及其稳定性 ;通过控制合理的工艺参数 ,获得了截面为圆形及近似弯月面形、表面质量和内部定向组织良好的样件 .     

钕铁硼稀土永磁材料室温熔盐电镀铝的研究

在钕铁硼(NdFeB)稀土材料表面直接进行水溶液电镀时,存在镀层分层、易起泡等缺陷.采用AlCl3/EMIC(1-甲基-3-乙基氯化咪唑)室温熔盐电解质在NdFeB永磁材料表面电镀铝,是提高其表面防护质量的有效方法.探讨了NdFeB永磁材料在室温熔盐中电镀铝的可行性、熔盐配比和芳香化合物对电镀铝层组织形态的影响,同时对镀层形成的机理进行了初步探讨.研究表明:采用AlCl3/EMIC室温熔盐电解质可在NdFeB永磁材料表面获得满意的铝镀层;铝镀层纯度很高,较完整平滑;添加芳香化合物可以大大提高镀层的质量,使晶粒细小、致密.     

Effect of selective laser melting on microstructure and properties of AZ91D alloy

Selective laser melting technology is used to manufacture porous and solid AZ91D alloys. The effects of laser power and hatch spacing on the density, blowholes, microstructure and mechanical properties of AZ91D alloy are studied. The laser power and hatch spacing play a significant role in the density and blowholes of AZ91D specimens. The grains size of specimens increases from 1 μm–2 μm to 8 μm–10 μm from the bottom to the top in single molten pool. Compared with grain size of die‐casting alloy (30 μm), that of selective laser melted gets refinement. There is no significant change in microstructure in the bottom, middle and top of specimens. The micro‐hardness of AZ91D alloy, reaching up to 115.3 HV 0.1, is superior to that of die‐casting alloy (56 HV 0.1). The compression properties of porous and solid specimens reach the degree of die‐casting solid magnesium alloy. AZ91D alloy shows the potential in the application of medical biodegradable materials.     

熔融碳酸盐燃料电池(MCFC)用γ-LiAlO_2粉末的制备

本文简介了熔融碳酸盐燃料电池(MCFC)及其优点;叙述了合成LiAlO_2的方法,用Al_2O_3(a,γ)成功地制得了稳定的适合于MCFC用的γ-LiAlO_2,在MCFC工作温度(923K)下,β-LiAlO_2是不稳定的;973-1073K时,β-LiAlO_2向γ-LiAlO_2转变速度明显增大;a-LiAlO_2要在1073K以上转变为γ-LiAlO_2.     

钢液氢含量检测技术研究

测量钢液氢含量的方法有离线定氢和在线定氢。离线定氢通过从钢液中取样,凝固后实验室检测氢含量。在线定氢通过测量出钢液的平衡氢分压后利用Sievert定律换算出氢含量。与离线定氢相比,在线定氢影响因素少,系统重现性好,测量周期短,满足真空处理、连铸等快节奏定氢的需要。