High cycle fatigue behaviour of Ti–6Al–4V alloy at elevated temperatures

High cycle fatigue behaviour of Ti–6Al–4V alloy was studied at 623 K and 723 K. Fatigue strength decreased at elevated temperatures compared with at ambient temperature. In the short life regime, fatigue strength was lower at 723 K than at 623 K, but in the long life regime it was nearly the same at both temperatures. At elevated temperatures, cracks were generated earlier at applied stresses below the fatigue limit at ambient temperature, indicating lowered crack initiation resistance. Small cracks grew faster at elevated temperatures than at ambient temperature, which became more noticeable with increasing temperature. After allowing for the elastic modulus, small cracks still grew faster at elevated temperatures.     

Diffusion of additives and plasticizers in poly(vinyl chloride): 4. A programmed temperature technique for the determination of the diffusion parameters of three dialkylphthalates

A programmed temperature technique has been developed for the measurement of the self-diffusion coefficients of additives in polymers. This has been applied to the diffusion of three dialkylphthalate plasticizers in poly(vinyl chloride). Values of the self-diffusion coefficients and the calculated activation energies obtained in this way have been compared with values previously obtained from measurements at constant temperature. It has been shown that the programmed temperature technique gives a very rapid method for the estimation of the activation energy of self-diffusion.     

Viscosity of compressed cold lake bitumen

Viscosity data over a temperature range of 37-115°C and a pressure range of 0-10 MPa gauge are presented for a Cold Lake bitumen sample. These data show that the compression of Cold Lake bitumen results in a significant increase in its viscosity. Results are compared with those from a similar study on an Athabasca bitumen sample. Also presented are two correlations for the effects of pressure and temperature on the viscosity of Cold Lake bitumen.     

纺牵—步法中粗旦丙纶长丝沸水收缩率初探

在纺牵联合一步法纺丝机上研究了丙纶切片的熔融指数对纤维沸水收缩率的影响，发现熔融指数高的切片，其纤维的沸水收缩率变化大。沸水收缩率随热定型的温度升高而下降。沸水收缩率可根据用户提供中心值（Ｍ）通过实验确定，一般以Ｍ±１．５为宜。     

浅谈一次盐水的工艺指标控制

介绍了一次盐水的各项工艺指标对生产的影响以及稳定控制这些指标的方法，强调了在生产中控制好一次盐水的工艺指标是影响产品质量及离子交换膜使用寿命的关键。     

窑炉用热电阻、热电偶智能温度测量板的设计

温度是影响陶瓷烧成质量的关键因素,介绍了一种适用于测量各种窑炉不同部位温度的智能温度测量板,由于该系统在不同的测温部位分别采用了热电阻和热电偶,克服了一般测温系统在连接不同的测温传感器需要更换不同的测温模板、成本高、使用不方便等不足,并具有适用性强、测温精度高等优点。     

PET熔体输送系统中熔体温度自动控制方案

在热媒温度控制系统中以熔体温度作为主参数,组成串极调节系统。投入运行后,熔体温度稳定,调节阀动作平稳,效果良好。     

6m大容积焦炉烘炉实践与体会

介绍了 6 m大容积焦炉由冷态到转入正常加热温度的烘炉操作过程中 ,按照一定的升温曲线 ,通过对焦炉热工和炉体膨胀的科学管理 ,确保新建焦炉顺利由冷态过渡到生产状态。     

环糊精和表面活性剂在室温磷光中的应用

介绍了环糊精和表面活性剂作为有序介质在室温磷光中的研究进展．并对各种方法的特点和应用情况作了简要概括。认为环糊精和表面活性剂混合介质能大大提高发光物质的室温磷光．而且操作简便．应用前景广阔。