Film morphology and reaction rate for the CVD of tungsten by the WF6—SiH4 reaction

Journal of Electronic Materials - Low pressure chemical vapor deposition (LPCVD) of tungsten (W) by SiH4 reduction of WF6 on Si(100) surfaces was studied in a single-wafer, cold-wall reactor over a...     

高强度船板纵裂纹的成因及预防

针对高强度船板纵裂纹轧后退废过高的现状，分析原因并优化冶炼、连铸工艺及操作，有效地降低高强度船板的退废率。     

Preparation of ultra fine nickel-copper bimetallic powder for BME-MLCC

The preparation of ultra fine nickel-copper bimetallic powder with two-stage chemical reduction method was investigated. Reductive sugar and hydrazine hydrate were employed as reducing agent in different reductive stage, respectively. Reaction of CuSO₄·5H₂O with reductive sugar at 70 °C gives cuprous oxide and copper particles, then as-prepared mixture and nickelous hydroxide were reduced by hydrazine hydrate, and nickel-copper powder having excellent dispersibility was prepared. Influences of nickel added on composition and dispersibility of powder were studied. TG/DTG/DTA of nickel-copper powder, which is stable in room temperature, were discussed with thermal analyzer. Relation of nickel content to oxidation temperature was investigated. Ni-Cu bimetallic powder particles have a fully coated structure when nickel content is up to 30%. As-prepared nickel-copper powder was applied in base metal electrode-multilayer ceramic capacitor (BME-MLCC). The end termination has high adhesion force, fairly good densification, low resistivity, excellent solderibility behavior and resistance behavior to soldering.     

Electrical properties at p-ZnSe/metal interfaces

In order to prepare low resistance ohmic contacts to p-ZnSn by the “deposition and annealing (DA)” technique which has been extensively used for GaAs and Si-based devices, formation of a heavily doped layer by the p-ZnSe/metal reaction is required. For p-ZnSe/Ni contacts, Ni and Se reacted preferentially at the ZnSe/Ni interface upon annealing at temperatures higher than 250°C. However, capacitance-voltage measurements showed that the net acceptor concentration (N_A-N_D) close to the p-ZnSe/Ni interface was reduced upon the Ni/ZnSe reaction, resulting in high contact resistance. For p-ZnSe/Au contacts, neither Au/ZnSe reaction nor reduction of the acceptor concentration were observed after annealing at temperatures lower than 300°C. This indicates that although the metal/p-ZnSe reaction is mandatory to prepare a heavily doped layer, the reaction induced an increase in the compensation donors in the p-ZnSe substrate. In order to increase the acceptor concentration in the vicinity of the p-ZnSe/metal interface through diffusion from the contact materials, Li or O which was reported to play the role of an acceptor in ZnSe was deposited with a contact metal and annealed at elevated temperatures. Ni or Ag was selected as the contact metal, because these metals were expected to enhance Li or O doping by reacting with ZnSe. However, the current density-voltage characteristics of the Li(N)/Ni and Ag(O) contacts exhibited rectifying behavior, and the contact resistances increased with increasing annealing temperature. The present results indicated that, even though the acceptor concentration in the p-ZnSe substrate increased by diffusion of the dopants from the contact elements, an increment of the compensation donors was larger than that of the acceptors. The present experiments indicated that preparation of low resistance ohmic contacts by forming a heavily doped intermediate layer between p-ZnSe and metal is extremely difficult by the DA technique.     

中性固色剂NF在分散／活性一浴热溶染色中的应用

本文对涤棉混纺织物在分散/活性染料同浴染色中采用碱固工艺与中性固色工艺作了较详细的对比试验,同时对中性固色剂及双氰胺的用量进行了优选组合,并对中性固色剂的效果进行了讨论。     

Dual reaction capacity of hydrogenated nanodiamond

High temperature hydrogen stream treatment of nanodiamond was shown to produce nanodiamond with bifunctional surface. OH- and different CH-groups were shown to be the main functional groups on the surface. In this article we proposed two main strategies for further chemical modification of hydrogenated nanodiamond. OH-groups were shown to react with different types of acylating agents: anhydrides and chloranhydrides. Chlorination of hydrogenated nanodiamond with molecular chlorine and its subsequent treatment with alkyllithium reagents resulted in formation of alkyl-nanodiamonds. Chlorination was shown to reduce the size of nanodiamonds aggregates. We have also applied suspension-state NMR-H1 spectroscopy to study suspensions of alkyl-nanodiamonds for the first time.     

真空阴极弧离子镀类金刚石碳（DLC）膜的碳弧稳定性研究

选用氩气、氩气加氢气、氩气加乙炔等气体作为介质，石墨作为靶材进行真空阴极弧离子镀来制备类金刚石碳膜。石墨电弧有其独特的电弧特性曲线，不同气体介质对碳弧特性的影响不同，磁场的大小对电弧的稳定性有很大作用，碳弧下基片偏流随电弧电压的增加而减小，试验得到表面光滑的类金刚石碳（DLC）膜，对膜的表面进行了SEM分析。     

混凝土抗硫酸盐侵蚀试验的一种新方法

提出了一个测定混凝土抗硫酸盐侵蚀能力的新方法。采用这种方法对超高强混凝土的抗化学腐蚀性能进行了试验，并和普通混凝土进行了对比。发现用一般硅酸盐水泥配制的超高强混凝土虽然在抵抗化学侵蚀能力方面比普通混凝土有所提高，但由于化学组成上的原因，它对高浓度的(NH4)2SO4等化学介质也难以抵抗。     

PREPARATION OF TiN FILMS BY N_2 ASSISTED Xe~+ ION BEAM ENHANCED DEPOSITION AND THEIR MECHANICAL PROPERTIES

A new method for preparation of hard TiN films has been developed by using electronbeam evaporation-deposition of Ti and bombardment with 40 keV Xe~+ ion beam ina N_2 gas environment.The synthesized TiN films were superior to PVD and CVDones in respects of improved adhesion to substrate and low preparing temperature.Theyexhibited good wear resistance and high hardness up to 2200 kg/mm~2.Some industrialapplications have been reported.     

Mobile learning in chemical engineering: An outlook based on case studies

In the context of the electronic learning (E-learning) methodology, mobile learning (M-learning) focuses on the use of portable technology (such as mobiles or tablets) and the mobility of students. E-learning, and particularly M-learning, can be implemented in combination with other pedagogical methodologies for chemical engineering teaching and learning. We can consider that the vast majority of undergraduates own personal mobile devices nowadays. Moreover, many case studies have shown that M-learning is an effective methodology to capture students’ attention and to actively engage them in the learning process. In most cases, lecturers have reported an improvement in both academic performance and qualifications and have expressed a favourable opinion towards this type of initiative in surveys. In line with the increasing interest in the incorporation of E-learning, this review discusses cases studies based on M-learning within the field of chemical engineering teaching through different technological platforms and apps which can be installed or directly used on mobile devices. All the platforms described in this work offer a free version, emphasizing the possibility of extending this methodology within the university with no need for additional economic resources.