基于SpatialWare的地理数据访问安全性研究

地理信息系统的应用越来越广泛,特别是基于网络的GIS的发展使地理空间信息通过网络被多用户所共享,因此必须考虑地理数据访问的安全性。文章以MapInfoSpatailWare空间数据引擎为研究对象,给出了基于此模式的数据访问安全性解决方案。     

包装件压力试验机计算机测控系统

针对YE-50包装件压力试验机落后的测控系统，提出一种基于压力和位移闭环控制的计算机测控系统。根据测得的压力、位移和设定值，通过模糊控制输出驱动伺服阀实现了压力试验时的恒速控制和堆码试验时的恒力控制。并实时显示力——位移及应力——应变曲线。文中还对模糊控制器的实验整定方法进行了探讨。     

硫化氢吸收液的电化学分解条件研究

理想的脱硫工艺应满足体积小、费用低、净化度高、无二次污染等要求。在碱性溶液吸收微量硫化氢时同步进行电解，可有效减小设备体积，并将硫化氢转变为氢气和硫磺，不产生恶性气味。为此，实验研究了温度、浓度、电流密度、pH值等因素对电解阳极过程的影响，确定了适宜的电解条件，并在该条件下进行了吸收实验。结果表明，在最佳电解条件下，硫化钠溶液能充分吸收天然气中经变压吸附提浓的硫化氢（800 mg/m³），吸收率大于99.9％。     

单片LCoS光学引擎中彩色LED照明系统设计

LCoS光学引擎作为整个背投的一个要组成部分，其照明系统显著地影响着LCoS背投的性能。详细分析了影响照明效果的各个因素，并利用ZEMAX软件设计出了单片LCoS光学引擎中基于彩色LED光源的照明系统，该系统能达到较好的亮度和均匀性，满足整个光机系统的成像要求。     

橡胶促进剂DM的合成工艺

M氧化生成DM是自由基反应机理，结合微反应器机理，采用分子氧化的反应方式，选用绿色溶剂异丙醇、环境友好型氧化剂H202，一步法制取高品质DM。对反应时间、反应温度、氧化剂用量等因素进行考察，确定最佳工艺条件为：反应时间90min，反应温度55℃，氧化剂不过量，碱过量5％，M—Na溶液M含量30％，加料时N60 min，溶剂用量为M—Na溶液质量的1．5倍，所得产品质量合格，熔点可达180℃。     

一种制氢预转化催化剂还原的新方法

对上海高桥分公司2×10~4m~3/h(标准状态)制氢装置原设计的预转化催化剂还原流程进行了改进。先跳开预转化反应器,利用转化炉制取氢气,再用自产的高纯氢气代替重整氢,对预转化催化剂进行单独升温还原,避免了催化剂在还原初期因发生甲烷化反应而超温失活的问题,使催化剂具有更好的活性和稳定性。     

Estimation and Optimization of the Principal H-Maser Parameters

The scale along the coordinate axes in the equations of motion hitherto used for an H-maser (in relative units) is shown to depend on Q as the quality factor for an H-maser. This hinders both analysis of the operation of the H-maser and optimization of its parameters. The modified equations of motion proposed here do not have that shortcoming. We determine the atomic flux into the bulb that gives the H-maser the best metrological characteristics.     

Fatigue limit evaluation of notches,small cracks and defects: an engineering approach

In this paper, the average stress method for the fatigue limit evaluation of stress raising geometrical features is revised and extended. In particular, an analytical close‐form approach was used and the linear elastic stress equations were modified by taking into account the effect of nominal stress on the local stress distribution. Hence, the average tangential stress was correctly evaluated over a distance of 2a₀, where a₀ was El Haddad's short crack constant, for long and small notches as well as for crack‐like notches. When this model is applied to a wide range of geometrical features subjected to mode I fatigue loading, the classical shape of the curves of the Kitagawa–Takahashi diagram was obtained for changes in crack‐like notch size. Similarly, notch sensitivity was estimated by reducing the notch tip radius. The accuracy of the proposed method in predicting fatigue limits was then checked by using experimental data taken from the literature and generated on testing specimens weakened by rounded and sharp notches as well as by small artificial defects.     

移动式宽频带高产额中子发生器

多用途中子发生器有着广阔的市场和应用领域 ,文章对移动式宽频带高产额中子发生器 ,在设计制造过程中所涉及到的技术难点 :绝缘尺寸小、频率适应范围宽、为中子管提供靶压的高压负载特性好等作了技术分析 ,使多用途中子发生器在更广阔的范围内应用 ,提供了广阔前景。     

Efficient Parallel Algorithms for Some Graph Theory Problems

In this paper,a sequential algorithm computing the aww vertex pair distance matrix D and the path matrix Pis given.On a PRAM EREW model with p,1≤p≤n^2,processors,a parallel version of the sequential algorithm is shown.This method can also be used to get a parallel algorithm to compute transitive closure array A^* of an undirected graph.The time complexity of the parallel algorithm is O(n^3/p).If D,P and A^* are known,it is shown that the problems to find all connected components,to compute the diameter of an undirected graph,to determine the center of a directed graph and to search for a directed cycle with the minimum(maximum)length in a directed graph can all be solved in O(n^2/p logp)time.