Capacitance behavior of activated carbon fibers with oxygen-plasma treatment

Modified activated carbon fibers (ACFs) were used as the electrodes of an electric double-layer capacitor and showed an enhanced capacitance effect after a RF-plasma treatment. The capacitance and the surface functional groups of the ACFs were studied. For the plasma-treated ACFs having a specific surface area of 1500 m² g⁻¹, the capacitance increased by 28% compared to the untreated sample and the highest electric capacitance value of 142 F g⁻¹ was achieved with an oxygen feed concentration of 10 vol.%. The Brunauer-Emmett-Teller (BET) surface area was 2103 m² g⁻¹, which was 34% higher than that of the untreated sample. The pore volume was similarly increased to 483.1 cm³ g⁻¹ STP, and from the pore distribution plot, quantities of mesopores of 10 nm or less and micropores also increased. However, in order to enhance the capacitance, the quinone functional group had a significant influence in addition to the BET surface area. The correlation between the capacitance and the number of quinone functional groups was confirmed because quinone is an electron acceptor.     

Modeling the tensile behavior of fiber bundles with irregular constituent fibers

In this article, the effect of fiber dimensional irregularities on the tensile behavior of fiber bundles is modeled with the finite element method. The fiber dimensional irregularities are simulated with sine waves of different magnitudes. The specific‐stress/strain curves of fiber bundles and their constituent single fibers are obtained and compared. The results indicate that fiber diameter irregularity along the fiber length has a significant effect on the tensile behavior of fiber bundles. For a bundle of uniform fibers of different diameters, all the constituent fibers will break simultaneously, regardless of the fiber diameter. Similarly, if fibers within a bundle have the same pattern and level of diameter irregularity along the fiber length, the fibers will break at the same time, also regardless of the difference in the average diameter of each fiber. In these cases, the specific‐stress/strain curve for the bundle overlaps with that of the constituent fibers. When a fiber bundle consists of single fibers with different levels of diameter irregularities, the specific‐stress/strain and load–elongation curves of the fiber bundle have a stepped or ladder shape. The fiber with the highest irregularity breaks first, even when the thinnest section of the fiber is still coarser than the diameter of a very thin but uniform fiber in the bundle. This study suggests that fiber diameter irregularity along the fiber length is a more important factor than the fiber diameter itself in determining the tensile behavior of a fiber bundle consisting of irregular fibers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2664–2668, 2004     

Measurement of Fiber/Matrix Interfacial Shear Stress at Elevated Temperatures

An apparatus for measurement of the fiber/matrix interfacial shear stress at temperatures up to 1100° is described. Equipment was used to measure interfacial properties as a function of temperature in two ceramic-matrix composites and one metal-matrix composite. In the composites where the thermal expansion of the matrix was higher than that of the fiber, the interfacial shear stress decreased with temperature. The opposite trend was observed in a system with low matrix thermal expansion. The change of the interfacial shear stress with temperature of all the composites studied can be fully explained by considering the fiber/matrix expansion differences.     

Fabrication and amplification of Rhodamine B‐doped step‐index polymer optical fiber

A step‐index polymer optical fiber (SI POF) containing Rhodamine B in poly(methyl methacrylate) (PMMA) has been fabricated by a preform technique. Fluorescence of different fiber lengths were observed and discussed. A high gain (23 dB) for a SI POF with 60‐cm length, 400‐μm diameter was obtained. The Rhodamine B content of the doped SI POF is 5 ppm‐wt. The signal wavelength providing the highest gain for a 60 cm SI POF is around 630 nm, and the optimum fiber length is about 60 cm at 10 kW launched pump power. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 681–685, 2004     

Effect of carbon fiber surface functional groups on the mechanical properties of carbon-carbon composites with HTT

The present investigation describes the quantitative measurement of surface functional groups present on commercially available different PAN based carbon fibers, their effect on the development of interface with resol-type phenol formaldehyde resin matrix and its effect on the physico-mechanical properties of carbon-carbon composites at various stages of heat treatment. An ESCA study of the carbon fibers has revealed that high strength (ST-3) carbon fibers possess almost 10% reactive functional groups as compared to 5.5 and 4.5% in case of intermediate modulus (IM-500) and high modulus (HM-45) carbon fibers, respectively. As a result, ST-3 carbon fibers are in a position to make strong interactions with phenolic resin matrix and HM-45 carbon fibers make weak interactions, while IM-500 carbon fibers make intermediate interactions. This observation is also confirmed from the pyrolysis data (volume shrinkage) of the composites. Bulk density and kerosene density more or less increase in all the composites with heat treatment up to 2600 °C. It is further observed that bulk density is minimum and kerosene density is maximum upon heat treatment at 2600 °C in case of ST-3 based composites compared to HM-45 and IM-500 composites. It has been found for the first time that the deflection temperature (temperature at which the properties of the material start to decrease or increase) of flexural strength as well as interlaminar shear strength is different for the three composites (A, B and C) and is determined by the severity of interactions established at the polymer stage. Above this temperature, flexural strength and interlaminar shear strength increase in all the composites up to 2600 °C. The maximum value of flexural strength at 2600 °C is obtained for HM-45 composites and that of ILSS for ST-3 composites.     

Liquid spouting of pulp fibers in a conical vessel

Pulp fibers can be spouted in water in a conical vessel. The entities which are spouted are fiber flocs rather than individual fibers. Synthetic fibers, which do not flocculate, cannot be spouted. For comparison, rigid spherical particles were spouted with water in the same conical vessel. Liquid spouting of rigid particles was similar to gaseous spouting. For pulp spouting, the minimum spouting velocity is proportional to the mass of fibers in the bed and inversely proportional to the diameter of the inlet. For rigid particles, the minimum spouting velocity is proportional to the height of the bed and inversely proportional to the square of the diameter of the inlet. A model for the minimum spouting velocity was developed for pulp spouting.     

热处理前后丙烯腈／溴乙烯共聚纤维的热性能和阻燃性能研究

分析了热处理前后丙烯腈／溴乙烯共聚纤维的热性能与溴乙烯含量、升温速率或热处理时间的关系，并对纤维的阻燃性与溴含量或热处理时间关系进行了研究。结果表明，溴含量的增加或热处理时间的延长对热稳定性和阻燃性的提高有较大影响，而且经热处理后纤维的阻燃性与溴无关。     

UV‐radiation–induced preirradiation grafting of methyl methacrylate onto lignocellulose fiber in an aqueous medium and characterization

The preirradiation method of grafting has been established by ultraviolet radiation. Methyl methacrylate (MMA) was grafted onto jute fiber in an aqueous medium. The variation of graft weight with UV‐radiation time, monomer concentration, and reaction time was investigated. The conversion of monomer into homopolymer and graft copolymer was evaluated. The graft weight passes through a maximum value (～ 122%) with UV‐radiation time. The optimum value of the monomer concentration was evaluated for maximum degree of grafting. Graft copolymerization of MMA onto lignocellulose fiber significantly increases the elongation at break (～ 65%) compared to that of the “as‐received” sample. However, a linear decrease on breaking load was observed with the increase of graft weight. The estimation of degree of grafting was achieved using an IR technique by correlating band intensities with the degree of grafting. Considering the water‐absorption property, the grafted sample showed a maximum up to 61% decrease in hydrophilicity compared to that of the as‐received sample. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1667–1675, 2004     

Ageing studies of pineapple leaf fiber–reinforced polyester composites

This experimental study evaluated the water absorption characteristics of pineapple leaf fiber (PALF)–polyester composites of different fiber content. The degree of water absorption was found to increase with fiber loading. The mechanism of diffusion was analyzed and the effect of fiber loading on the sorption kinetics was studied. The diffusion coefficient was calculated and found to increase with fiber content. Studies were also made to correlate water absorption with the cross‐sectional areas of the specimens. The effects of ageing on the tensile properties and dimensional stability of PALF polyester composites were studied under two different ageing conditions. Ageing studies showed a decrease in tensile strength of the composites. The composite specimens subjected to thermal ageing showed only a slight deterioration in strength. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 503–510, 2004     

Study of needle penetration speeds on frictional properties of nonwoven webs: A new approach

H1 technology needlepunching machinery is one of the recent developments in the needleloom technology. H1 technology needlepunching nonwoven machinery has been effectively utilized to develop a set of nonwoven substrates at different punching rates. The effect of needlepunching speeds on the frictional properties of H1 technology polyester nonwoven webs is reported in this article. The frictional properties of nonwoven webs have been characterized using a simple normalized friction factor. In addition, the surfaces of the nonwoven substrates were scanned using scanning electron microscopy. The results show that for the three different penetration rates studied there seems to be a marginal difference in the frictional properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3626–3631, 2003