以YAG为添加剂的气压烧结氮化硅

本文以添加ＹＡＧ的反应烧结氮化硅（ＲＢＳＮ）为前驱体，采用气氛加压烧结的工艺，在０．５～９．０ＭＰａ氮气压力范围，研究了不同氮压对烧结体的密度、相组成、强度和显微结构的影响及其相互间的关系。研究表明，通过改变氮气压力能有效地调控材料的显微结构，材料的性能又受控于显微结构的变化。     

CFRP强度复合Weibull分布的物理特征分析

本文对ＣＦＲＰ材料疲劳后剩余强度的复合Ｗｅｉｂｕｌｌ分布的物理特征进行了初步分析。指出树脂基复合材料失效（破坏）机理的双重性（基体和纤维失效模型）决定了剩余强度（累积损伤程度）测试结果的分布特征。复合Ｗｅｉｂｕｌｌ分布曲线的特征与分析结果对设计、使用及材料研究都有重要参考意义。     

使用混合杆柱时抽油泵柱塞的超冲程

任何抽油杆柱在理论上都可能产生超冲程，只是大小不同而已。超冲程的存在，使泵柱塞的有效冲程增大，甚至会大于光杆冲程。首次提出了抽油泵柱塞相对超冲程和绝对超冲程的概念，这将有助于正确认识玻璃钢抽油杆的作用和玻璃钢抽油杆的推广使用。将抽油杆柱简化成上端受光杆的激振位移、下端带有集中质量的弹簧－质量力学模型，建立了抽油杆柱纵向振动的偏微分方程和边界条件，然后用固有函数法求解方程，得出了抽油泵柱塞超冲程的无穷级数解析计算式。     

低合金高强度钢的微观组织和疲劳裂纹扩展行为

用透射电镜观察了３０ＣｒＭｎＳｉＮｉ２Ａ钢等温的微观组织，疲劳裂纹扩展行为、裂纹尖端塑性区和位错结构，结果表明，等温状态组织由马氏体和贝氏体组成。在一个奥氏体晶粒内一般存在四个板条领域、裂纹尖端的塑性区内存在主位错带，疲劳断裂的基本组织单元为板条晶或板条束。裂纹遇到板条束界时方向发生较大偏斜。     

Prediction of High-Temperature Long-Term Strength for Damaged Structures

A method is proposed for analytical estimation of the high-temperature long-term strength of structures with material discontinuities, which are stress raisers. We consider the processes involving the formation of diffusion pores. Diffusion processes in metals are strongly enhanced with increasing temperature and stresses.     

预测井眼稳定性的力学化学耦合方法

在井眼力学稳定性评价的基础上，将硬脆性页岩水化后岩石强度等参数的变化规律用于页岩水化前后坍塌压力变化的对比分析，结果表明，地层坍塌压力当量密度随页岩水化程度的增加逐渐升高。给出了预测井眼稳定性的力学化学耦合方法，并将该方法应用于现场生产中，取得了较好的预测效果     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

几种高强度钢腐蚀疲劳裂纹扩展行为的研究

本文研究了ＧＣ－４，３０ＣｒＭｎＳｉＮｉ２Ａ和３００Ｍ超高强钢的腐蚀疲劳裂纹扩展行为。考虑了环境，热处理制度，应力比和频率对裂纹扩展的影响。研究结果表明：腐蚀环境和热处理制度对疲劳裂纹扩展有显著影响。在侵蚀性环境中随频率降低，裂纹扩展大幅度上升，随应力比提高，环境影响加剧。利用扫描电镜对试样断口形貌进行了分析，并讨论了高强钢的腐蚀疲劳机理。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。