Prediction model of compressive strength development of fly-ash concrete

Based on experimental results concerning the compressive strength development of concrete containing fly ash, the authors derived an estimation equation for compressive strength development. The equation can express coefficient , which indicates the activity of fly ash as a binder, in the form of a function of age, fly-ash content, and Blaine specific surface area of fly ash.

This equation is capable of explaining the increases in the early strength due to fly ash in place of part of fine aggregate, the decreases in the early strength due to fly ash in place of part of cement, the increases in the long-term strength due to pozzolanic reaction, the relationship between the fly-ash replacement ratio and the ratio of strength increase/decrease, and the effect of fly ash's Blaine specific surface area on the strength.     

An Experimental Study of Fatigue Strength for Adhesively Bonded Tubular Single Lap Joints

In this paper, manufacturing technology of the tubular single lap adhesive joint was studied to obtain reliable and optimal joint quality. In addition, a surface preparation method and a bonding process for the joint were devised. The effect of the adhesive thickness and the adherend roughness on the fatigue strength of the joint was experimentally investigated. From experiments, it has been found that the fatigue strength of the joint increased as the adhesive thickness decreased and the optimal arithmetic surface roughness of the adherends was about 2 μm.     

运动与减肥

通过分析肥胖的病因学、运动减肥原理得出,非药物性的适量运动具有经济、有效、无副作用等优点,有利于各年龄段的人降脂减重,并能抑制体重反弹。     

对于水泥物理性能检测问题的研究

具体分析了水泥的细度、凝结时间、胶砂强度等物理性能的检测过程,以供参考。     

CGA560增强助磨剂在水泥粉磨中的应用研究

研究了CGA560增强助磨剂在水泥粉磨中对台时产量和水泥质量的影响。试验结果表明:在磨机状况不改变的条件下,CGA560增强助磨剂的加入可提高磨机产量10%-30%;同时可有效减少过粉磨现象,优化水泥颗粒级配,提高了水泥粉磨细度及比表面积;因而使水泥强度等性能得到了明显改善和提高。     

Adhesive bonding of stainless steel water tubing

The use of an adhesive to bond stainless steel water tubing, allowing stainless steel fittings to be employed, is considered and compared with the more conventional use of compression or capillary copper fittings together with a soft solder. Tests carried out to determine environmental effects on adhesively bonded stainless steel tubing suitable for domestic water supply, and the strengths of these joints, are described. It has been found that acrylic anaerobic adhesives are suitable for bonding tubing carrying cold water, the joints attaining superior strength to the copper-soldered ones; a reasonable degree of flexing can also be tolerated. It would appear that certain selected adhesives may also be used in joints carrying hot water.     

胶层厚度对拉伸试样应力分布影响的数值分析

运用弹塑性有限元法研究了胶层厚度对承受拉伸载荷的对接接头胶层内应力分布的影响．三维有限元法数值分析的结果表明，随胶层厚度减小，胶层中正应力SZ与剪应力SYZ的分布趋于均匀；而对正应力SY而言，胶层厚度为0．15mm时，其边缘峰值应力最低。     

Effects of apitong (Dipterocarpus spp.) extractives on bond strength development and curing rate of adhesives

Emulsion polymer isocyanate ( ), polyvinyl acetate ( ) and resorcinol-formaldehyde ( ) adhesives were used to produce single lap shear specimens using resinous and non-resinous apitong (Dipterocarpus spp.) timbers. Tests showed that joints made with highly resinous apitong were about 40% weaker than similar joints made with non-resinous apitong. The resinous apitong was treated with different solvents to yield five different extractives which were characterized by infra-red analysis. Apitong extractives were then added to and adhesives and joints made with buna (Fagus crenata), a timber known to be low in extractives and easy to bond. Joints prepared using extractive-containing adhesives were generally weaker than those made with the unmodified adhesives. RF adhesives containing extractives cured more slowly than unmodified . It is thought that the acidic nature of the extractives changes the pH of the system sufficiently to affect the curing mechanism     

Rheology of cementitious paste with silica fume or limestone

The rheological behaviour of cementitious pastes where cement has increasingly been replaced by densified silica fume (SF), untreated SF or limestone has been studied. The effect of SF on the flow resistance, taken as the area under the flow curve, was found to depend on the dispersing ability of the plasticizer as illustrated by pastes with naphtalene sulphonate-formaldehyde condensate (SNF) and polyether grafted polyacrylate (PA).The gel strengths increased with increasing SF replacement of cement independently of plasticizer type. The cementitious gel strength was, however, depending on the type of SF since pastes with densified SF developed lower gel strengths than pastes with untreated SF. This phenomenon was attributed to agglomerates in the densified SF which remained unbroken by the mixing and measurement sequence.Both flow resistance and gel strength decreased with increasing limestone replacement. Thus, silica fume may have an advantage over limestone filler as stabilizing agent for self-compacting concrete preventing segregation upon standing and reduced form pressure due to a more rapid gel formation.     

树脂增强选择性激光烧结多孔金属件的研究

针对选择性激光烧结(SLS)间接方法成型的金属零件形坯,经脱脂和高温烧结后形成的零件存在大量孔隙和空洞,其致密度和强度都较低,不能满足实际应用要求的问题,采用改性耐高温环氧树脂浸渗零件烧结坯的方法,使多孔金属件致密化,并粘结内部金属网架,提高零件的机械性能.对浸渗烧结坯的拉伸强度的测试和扫描电镜(SEM)以及热失重(TGA)的分析结果表明,浸渗树脂后的烧结坯拉伸强度提高了约4倍;改性环氧树脂和金属网架粘结在一起,形成一个密实的网络结构,致密度大幅提高;零件可在200℃的温度下使用.该方法可以制造注塑模具和功能零件.