熔盐堆临界能谱与通量分布的仿真计算

研究熔盐反应堆在临界工况下的堆芯中子能量和中子通量分布.由于熔盐反应堆的几何结构与目前的热中子反应堆存在很大差异,导致热中子反应堆能谱的求解方法在对熔盐堆进行计算时存在几何处理上的困难.针对上述问题,提出采用具有任意几何处理能力的中子输运计算软件MCNP对熔盐堆堆芯结构进行建模,采用能量区间上的平均通量代替该区间内通量分布的方法,计算了两种熔盐堆在临界工况下的堆芯中子能谱.结果表明,MSBR堆芯能谱为典型的热堆能谱;MO-SART堆芯能谱介于快堆能谱和热堆能谱之间.结果能够作为堆芯扩散计算中能量分群方法的依据.同时分析了堆芯内中子通量分布情况,结果表明熔盐堆中子通量分布具有中间高、四周低的特点.     

由液体密度和蒸发焓关联纯物质的临界参数

本文提出了一个由液体密度和正常沸点下蒸发焓数据推算物质临界参数的新方法。本方法所需数据为：液体密度、ＺＲＡ值及正常沸点下蒸发焓。采用本文方法对有代表性的近１００种有机物和１６种无机物的Ｐｃ和Ｔｃ值进行了估算，结果表明本文方法稳定、可靠。     

Implications of particle size to transient stage of deep bed filtration

This study was aimed at investigating the effect of particle size, mostly in the submicron range, on break-through stage of filtration. Latex beads, with diameters ranging from 0.46- to 2.967-μm were filtered through filter grains of diameters 0.1-, 0.175- and 0.45-mm. Experimental conditions were chosen so as to obtain breakthrough curves. The experimental results showed that the initial efficiency follows the pattern reported by previous experimental and theoretical studies, i.e., lower efficiency for 0.825-μm particles which fall in the range of critical size. However, the particle removal during the transient stage increased with an increase in particle size for the range of sizes studied. This pattern is qualitatively confirmed by the theoretical predictions of Vigneswaran and Chang (1986) model. This study also provides experimental verification of the effect of the ratio of particle size and grain size at different stages of filtration.     

多支化两亲聚合物合成及其原油乳化作用研究

通过自由基胶束共聚法制备了N-苄基-N-n-十六烷基丙烯酰胺/丙烯酰胺/丙烯酸钠三元共聚两亲聚合物-P(AM/BHAM/NaA),并优化了合成方案。该聚合物具有临界聚集浓度(CAC),当该两亲聚合物质量浓度高于700mg/L时,P(AM/BHAM/NaA)在水溶液中形成聚集体,并随着聚合物质量浓度的增加聚集体的流体力学半径增加,表观黏度也随之增加。P(AM/BHAM/NaA)具有良好的原油乳化能力,研究了不同质量浓度的两亲聚合物对原油乳化性能。结果表明,随着两亲聚合物质量浓度的升高,在水溶液中形成聚集体的体积增大,空间网络结构增大,乳化能力升高。     

Enhancement of ultrabroadband Bi NIR emission via fluorination for all wavelength amplification of optical communication

Bismuth (Bi)-doped photonic glasses and fibers with broadband near-infrared (NIR) photoemission have potential applications in tunable lasers and broadband amplifiers. Yet, when it comes to all wavelength amplification of optical communication, it remains challenging to achieve efficient Bi NIR emission in the technically relevant C- and L- bands (1530-1625 nm). Here, we propose a scheme by fluorination triggered enhancement of ultra-broadband Bi NIR emission in nitrided germanate glasses. Besides, compared to previous research, a unique and efficient Bi-activated ultra-wideband NIR emission with new emission bands peaked at ~924 and ~1520 nm under excitation of 450 nm are obtained in nitrided germanate glasses after fluorination. Moreover, the fluorination can modulate the local chemical environment by forcing the conversion of aluminum species from AlO₄ to AlO₅ and AlO₆ and consequently increase the flexibility of the glass network structure, which finally induces the conversion of Bi species and then manipulates the relative emission intensity of different Bi NIR centers. Thus, a flat and tunable emission spectrum covering the entire optical communication band is obtained by optimizing the fluoride amount. We believe this work is helpful to design the Bi-doped tunable fiber lasers and ultra-broadband amplifiers for all wavelength amplification of optical communication.     

A New Research Infrastructure for Investigating Flow Hydraulics and Process Equipment at Critical Fluid Properties

An optimized equipment design for natural gas processing and liquefaction plants becomes increasingly difficult with changing process conditions: Particularly low values of surface tension create rising challenges on the design of phase separators and column internals. The TERESA test rig at HZDR was designed to allow the investigation of multiphase thermohydraulics and phase separator performance under critical fluid properties in industrial dimensions. A versatile pipe test section is available in DN200 and equipment internals may be tested in a sectional DN300/DN500 test separator. The applied test fluid shows a high vapor-liquid density difference between 1470 and 940 kg m⁻³, viscosity as low as 0.12 mm²s⁻¹, and surface tension down to 1.3 mN m⁻¹. Volumetric liquid and vapor flow rates may be varied up to 9 and 530 m³h⁻¹ in the test rig, respectively.     

Microstructure of a nitrided steel previously decarburized

In this study the effects of a surface-controlled decarburization on the structure of a nitrided steel are analyzed. Samples of a quenched and tempered 42CrMo4 steel were decarburized by heating in air at different depths and submitted to gaseous nitriding. After decarburization and nitriding, the microstructure of surface layers was investigated by optical microscopy (OM) and scanning electron microscopy (SEM). The nitrogen and carbon profiles in the diffusion layers were determined by SEM equipped with a wavelength dispersive spectrometer (EPMA-WDS) and by glow discharge optical spectrometry (GDOS). The effect of nitriding was determined by microhardness measurements. Our results indicate that a previous decarburization only slightly affects the surface hardness, but reduces the conventional nitriding depth. The decarburization also favors the nitrogen take-up and produces increased nitrogen concentrations in the compound layer and in the narrow zone beneath it.     

板材轧制问题中的变形与应力

根据全息干涉法对板材轧制成形中的变形进行分析，假设三种典型轧制板的截面形状模型，计算了纵向非均匀应变分布，给出了其所产生的残余应力及其失稳起皱时的临界参数计算公式。与实测结果比较，变形的最大误差为11％。     

Development of the active balancing device for high-speed spindle system using influence coefficients

A high-speed spindle can be very sensitive to rotating mass unbalance which has harmful effect on many types of rotating machinery. Therefore, the balancing procedure is certainly needed to reduce vibration in all high-speed rotating systems. In this study, an active balancing program using influence coefficient method and an active balancing device of an electro-magnetic type with both simple and reliable structures were applied to the developed high-speed spindle system. A gain scheduling control using influence coefficients of the reference model was proved to be effective in balancing the spindle system although its characteristics were changed. The stability of reference influence coefficients was verified by experiments with frequency response functions. The active balancing experiment of the manufactured spindle system using an active balancing program and device was also performed efficiently during the operation. As a result, controlled unbalance responses after balancing work were below the vibration limit at all rotating speed ranges including critical speeds.     

φ50mm穿孔机后台架的改进

运用力学方法建立了穿孔机后台架的力学模型，导出了顶杆挠度曲线方程，给出了顶杆临界压力及顶杆长度之间的关系式，为穿孔机后台架的改进提供了理论依据。