电梯用含氮节镍奥氏体不锈钢QN1701的组织和性能

借助Thermo-Calc热力学相图计算软件,开发了用于电梯的含氮节镍奥氏体不锈钢QN1701(12Cr17Mn7Ni2Cu2N),以代替443(019Cr21CuTi)超纯铁素体不锈钢。通过OM、SEM和电化学工作站等方法研究了QN1701和443不锈钢的组织及性能。N原子起着间隙固溶和细晶强化的作用,使QN1701不锈钢的屈服强度提高至400 MPa以上,达到443不锈钢的1.32倍。QN1701不锈钢的点蚀电位为241 mV,低于443不锈钢的289 mV,但其点蚀速率为9.10 g/(m2·h),低于443不锈钢的14.58 g/(m2·h)。在电梯用研磨拉丝表面状态下,QN1701不锈钢在质量分数为10%NaCl中性盐雾和干湿循环盐雾等加速腐蚀试验中的耐蚀性能均优于443不锈钢。分析发现,443不锈钢添加一定量的Nb、Ti稳定化元素所生成的(Nb,Ti)(C,N)析出相经研磨拉丝处理后,暴露于表面或被拖拽后留下微坑,导致其耐蚀能力急剧下降。综上所述,相较443不锈钢,QN1701不锈钢具有强度更高、伸长率更大和在研磨拉丝表面状态下耐蚀性更好等特点,这对于电梯轻量化设计和长寿命具有重要价值。     

淬火温度对铸造Fe—B—Ti合金组织和性能的影响

通过不同的热处理淬火温度改变铸造Fe—B—Ti合金的组织，探讨了铸造Fe—B—Ti合金不同组织与性能的关系。试验结果表明：淬火温度较低时，硼化物变化较小，网状分布趋势明显；淬火温度较高时，硼化物断网和团聚化趋势明显加快。淬火温度1050℃时，硼化物网状特征消失，基本上都变成了团块状、颗粒状和杆棒状分布。随着淬火温度升高，硬度和韧性增加，超过1000℃，硬度和韧性变化不明显。淬火温度1050℃时，综合性能良好。     

印制板化学镀镍

介绍了采用金属Zn粒子悬浮液活化要镀镍的印制板(PCB)Cu电路表面,使其可以进行化学镀镍的工艺方法,它可以克服Pd-Sn活化的缺点.     

六方BN微颗粒表面化学镀Ni及动力学模型

以肼为还原剂在平均粒径为104μm的BN颗粒表面进行了化学镀Ni，提出了近球形颗粒表面“扩展-缩小自催化沉积”模型，较好地解释沉积量随时间的变化规律．依此模型推导了化学镀Ni沉积过程的动力学表达式．观测了不同沉积时间表面沉积Ni颗粒的SEM形貌变化规律，证实了动力学模型的正确性。     

NICKEL-BASED ALLOYS IN GE AIRCRAFT TURBINES：PAST,PRESENT ＆ FUTURE

1. Introduction Freedom to travel anywhere in the world, both quickly and inexpensively, defines our modern era. Despite year-to-year variation, the long term demand for travel by airplane continues to grow. Three ma- jor systems comprise the modern airplane: the aircraft structure that encompasses the fuselage, wings, and landing gear; the avionics that enable flight through crowded skies in nearly all weather conditions; and the propulsion system that powers the aircraft. Improvements in mat…     

Preparation of carbon nanotube composite material with metal matrix by electroplating

It is demonstrated that the nickel can be deposited directly on the surface of carbon nanotubes without pre-sensitization by Sn^2＋ and Pd^2＋ in a watt bath containing suspended nanotubes by electroplating. The nickel is deposited as spherical nanoparticle on the nanotubes. By increasing reaction time, the carbon nanotube is fully coated with nickel. A probable model, which represents the formation process of carbon nanotube-nickel composites by electroplating, is presented. The results show that this method is efficient and simple for preparing carbon nanotube-metal composite.     

预压缩单晶镍基合金的组织结构及在拉伸蠕变期间的粗化特征

对[001]取向单晶镍基合金进行压应力处理，获P-型筏状结构后，对其进行拉伸蠕变性能测试及SEM形貌观察，研究了P-型筏状结构的粗化特征及影响因素。结果表明：由于应力场的差别，样品不同位置筏状γ＇相粗化程度及特征不同，近断口处筏状γ＇相扭曲且粗化程度加剧，随离断口距离增加，γ＇相粗化程度减弱。有限元分析认为：外加载荷改变了水平和垂直γ基体通道中的错配应力分布，并使立方γ＇相不同界面晶格发生挤压或扩张应变，这可以促进元素的互扩散和γ＇相的定向生长，是形成P-型筏状组织的主要原因。在高温及拉应力作用下，P-型γ＇相端部沿垂直于应力轴方向优先生长和相互横向连接，并进一步形成折叠的层状组织。     

Interaction between erosion and high-temperature corrosion of metals: The erosion-affected oxidation regime

The combined erosion-oxidation of nickel, cobalt, and the oxides of these metals have been studied at 780°C in air to examine two regimes of interactionnamely, a regime of erosion-enhanced oxidation during which an oxide scale of constant thickness covers metal specimens, and a regime of oxidation-affected erosion that is characterized by a composite surface layer of metal, oxide, and erodent. In the case of cobalt, these two regimes have been documented and the transition from one regime to another described. For the range of conditions examined, only the oxidation-affected erosion regime was observed for nickel due to its lower oxidation rate compared to cobalt.     

Microstructure and Sliding Wear Behaviour of Ni(Cr)-TiB_2 Coatings Deposited by HVOF Spraying of SHS Powders

THERMAL SPRAYING provides a large range ofcoatings,which increase the wear resistance ofsubstrates[1].One of the major coating families is thecermet,composed of hard ceramic particles with ametallic binder.The most commonly used cermetcoatings in industrial applications are based on eitherthe WC-Co or the Cr3C2-Ni(Cr)systems with WC-17wt%Co and Cr3C2-25wt%Ni(Cr)being typicalcompositions[2,3].Although WC-Co deposits are hardand wear resistant at ambient temperatures their rangeof ap…     

Effects of phosphorus addition on the magnetic properties of sintered Fe-50 wt.% Ni alloys

Phosphorus was added to Fe-50 wt.% Ni in the form of a coated composite powder via an electroless plating process. Addition of phosphorus to Fe-50 wt.% Ni facilitated increases in density and grain size, both of which were beneficial to magnetic performance. Because of the homogeneous distribution of phosphorus in the powder, the optimal phosphorus addition was much lower than for those using Fe₃P as the phosphorus precursor. The optimal phosphorus addition was close to its maximum solubility in Fe-50 wt.% Ni (about 0.5 wt.%), above which precipitation of excessive phosphorus in the form of iron nickel phosphide, (Fe,Ni)₃P, effectively degraded the magnetic properties of Fe-50 wt.% Ni. Without the addition of phosphorus, good magnetic properties could be achieved only when the sintering temperature was high enough (>1200 °C) to result in a high sintered density and large grains in the sintered structure.