注入种子CuBr激光器中的光谱控制

报道了采用注入种子方法．对ＣｕＢｒ激光器进行激光模式控制的实验结果。实现了单纵模ＣｕＢｒ激光脉冲的注入放大，获得了功率为１００ｍＷ水平的窄线宽铜激光辐射．在理论上分析了短脉冲高增益激光器中注入种子过程，讨论了在注入种子ＣｕＢｒ激光器中进行光谱控制的实验结果．     

临盘油田分层注水管柱有效率影响因素分析

分层注水管柱有效率低一直是困扰临盘油田开发生产的一大难题。针对这一现状，在分析油藏结构、施工工艺和现场资料的基础上，分析了影响分层注水井管柱有效率的因素，阐述了封隔器、工艺操作、管枉自身及温度等制约分层注水管柱有效率提高的原因，并提出了相应的对策和措施。     

注塑件/模具成本评估方法研究综述

对注塑模成本评估领域的主要研究方法进行了分析 ,指出了相关的几个成本评估流派。着重对成本评估的CEF方法进行了总结 ,并对当前国际上流行的派别的优缺点进行了总结。文末 ,给出了我们的研究思路大体概述     

注气井中油管轴向位移计算比较分析

为了确定油管在正常作业、注入措施作业中封隔器的坐封位置、轴向位移补偿量以及判断封隔器是否解封,根据弹性力学理论得出了不同条件下油管柱的轴向位移量,综合考虑了在不同工况下由活塞效应、螺旋弯曲、径向压力、温度变化、松弛力以及摩阻等因素引起的油管轴向位移;同时考虑了在注气油管内气体的横向压力效应,运用VB语言编制程序,将各自计算结果进行了比较分析。结果表明,在注气油管内考虑横向压力效应时与常规油管长度计算油管轴向位移有明显差异;油管内液体流动引起的油管轴向伸长与注入速度的平方成正比,在注入速度过大时对轴向位移有明显影响。     

Advances in titanium metal injection molding

The approaches to production of titanium powder injection molded parts are reviewed. Historically, oxygen levels have been too high for structural use (particularly with the Ti-6Al-4V alloy). However, recent advances in starting powders, binders and sintering facilities now allow oxygen levels in the Ti-6Al-4V alloy to be controlled to about 0.2 wt.% oxygen. This should result in significant expansion of the titanium PIM market place into aerospace, automobiles, surgical instruments, dentistry, communication devices (such as computers and cell phones), knives and guns. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 5–6 (455), pp. 118–125, 2007.     

MARK-Ⅳ型气化炉气化剂均布的探讨

通过对炉篦的结构分析 ,并考虑炉内搅拌器的作用 ,结合原料煤的特性 ,提出气化剂均布的原则及方案 ,以改善气化炉操作功效     

Current collecting efficiency of micro tubular SOFCs

In this study, current collecting efficiency of the micro tubular solid oxide fuel cell (SOFC) was estimated to determine optimum size of the micro tubular SOFC. Two models for collecting current from single terminal (ST) and double terminal (DT) of anode tube were proposed and used to calculate the current collecting efficiency as functions of anode thickness, tube length and operating temperature. It was shown that design of the cell geometry and current correcting method are significantly important to achieve high performance micro tubular SOFC stacks. The efficiency loss estimated from the DT model was about 2–4-fold lower than those of obtained from the ST model. The DT model was shown to be more effective for higher operating temperature and the tube length.     

Simulation of Natural Depletion and Miscible Gas Injection Effects on Asphaltene Stability in Petroleum Reservoir Fluids

Natural depletion of petroleum reservoirs as well as gas injection for enhance oil recovery, are unavoidable processes in the oil industry. Foremost, prediction of the problems due to these two processes is very necessary and important. So many field and experimental experiences have shown that heavy organic depositions, especially asphaltene deposition, are principal results during these processes. Results of laboratory simulation of asphaltene deposition during the natural depletion of petroleum reservoirs and also during gas injection and enhanced oil recovery (EOR) processes are reported here. This is achieved through the design of a new experimental setup for the investigation of pressure and composition effects on asphaltene deposition in petroleum fluids at high pressure and high temperature conditions. In this work, asphaltene deposition during decreasing pressure, from pressures greater than reservoir pressure to pressures below the bubble point pressure (natural depletion) and also asphaltene deposition during natural gas injection in reservoir conditions, are studied for three samples—one recombined sample and two bottomhole samples. All of the obtained results from this work conform to theoretical and other experimental works.     

高炉喷吹半焦的可行性

本文介绍了煤的热解和半焦性质。煤在快速热解过程中脱除热解水、焦油、部分的硫和煤气。半焦含有比煤低的硫含量和较高的热值。半焦的可磨性、反应性及燃烧性都比煤好，因此，半焦是高炉理想的喷吹燃料。     

高炉炉缸内铁水环流与内衬侵蚀

从分析中心焦柱在炉缸内的受力出发，计算了１０００￣５５８０ｍ＾３高炉大喷煤前后中心焦柱在炉缸铁水内的沉入深度，分析了炉缸内铁水环流的产生与炉缸内衬侵的关系，分析表明大喷煤有得利抑制铁水环流对缸内补的冲刷，提出了降低铁水环流对炉缸内衬侵蚀的途径。