台阶式溢流坝消力池压强特性试验研究

为研究台阶式溢流坝不设反弧段连接时消力池底板压强特性,结合某水库实际工程,采用物理模型试验方法,对台阶式溢流坝消力池底板时均压强、脉动压强强度和峰值等压强特性进行了研究。结果表明,消力池底板时均压强均为正值;在滑行水流和过渡水流时,时均压强在水流冲击区出现一个较大值,最大为0.926kPa,下游反弹区形成极小值;在跌落水流时,时均压强沿程变化较小,且随流量的增加而增大;脉动压强强度和峰值沿程变化规律基本一致,总体上随流量的增加而增大,最大值出现在水流冲击区,脉动压强最大为1.198kPa,随后沿下游方向逐渐减小,并趋于稳定;台阶尺寸对消力池底板时均压强和脉动压强影响不大;消力池内脉动优势频率为0.01~4 Hz,属低频振动,不会危害泄水建筑物的安全。研究成果可为台阶式溢流坝消力池的优化设计提供参考。     

基于MIKE FLOOD的洪泽湖周边滞洪区洪水演进模拟研究

基于实测断面资料建立了研究区的一维水动力模型,基于高精度DEM以及1∶10000地形图建立了研究区的二维水动力模型,并用MIKE FLOOD将一维模型和二维模型进行耦合,构建了洪泽湖周边滞洪区一、二维耦合的洪水演进数学模型。利用2003年历史洪水资料对模型参数进行了率定,并以2007年历史洪水资料进行了验证。以洪泽湖百年一遇设计洪水为模型上边界,二河闸、三河闸以及高良涧闸的现行调度方案的水位-流量关系为模型下边界,对洪泽湖百年一遇设计洪水方案进行模拟计算,当蒋坝水位达到14.33m时,洪泽湖周边滞洪区开始滞洪,得到开始滞洪后不同时段研究区内各类洪水风险要素的动态分布情况以及最大淹没水深、淹没历时,验证了模型的合理性,可用于蓄滞洪区洪水演算分析。     

管道化溶出系统中大型套管式换热器的热补偿设计及组焊

以单内管套管式换热器为例 ,分析了管道化溶出系统大型套管式换热器热补偿的设计方法 ,重点分析了内外管膨胀差的补偿及其弯管部分的结构设计。另外 ,对一些与热补偿相关的结构 ,如封闭环的设置也进行了必要的分析     

Double auction mechanisms on Markovian networks

This paper studies the double auction (DA) mechanism in Ma and Li (2011) for a class of exchange economies. We extend their results to more general cases where sellers and buyers each form a complex time non-homogeneous Markovian chain, as specified in Ram et al. (2009), in the communication of their private information. A numerical example is also provided. Both bubbles and crashes are observed in the example, consistent with results of our theorems. Our example and theoretical results provide new evidence that a DA mechanism, widely utilized in real exchange markets, may contribute to the excess volatility identified in Shiller (1981) and LeRoy and Porter (1981).     

Biomimetic strain hardening in interpenetrating polymer network hydrogels

In this paper, we present the systematic development of mechanically enhanced interpenetrating polymer network (IPN) hydrogels with Young's moduli rivaling those of natural load-bearing tissues. The IPNs were formed by synthesis of a crosslinked poly(acrylic acid) (PAA) network within an end-linked poly(ethylene glycol) (PEG) macromonomer network. The strain-hardening behavior of these PEG/PAA IPNs was studied through uniaxial tensile testing and swelling measurements. The interaction between the independently crosslinked networks within the IPN was varied by (1) changing the molecular weight of the PEG macromonomer, (2) controlling the degree of PAA ionization by changing pH, and (3) increasing the polymer content in the PAA network. Young's moduli and the maximum stress-at-break of the swollen hydrogels were normalized on the basis of their polymer content. Strain hardening in the IPNs exhibited a strong dependence on the molecular weight of the first network macromonomer, the pH of the swelling buffer, as well as the polymer content of the second network. The results indicate that the mechanical enhancement of these IPNs is mediated by the strain-induced intensity of physical entanglements between the two networks. The strain can be applied either by mechanical deformation or by changing the pH to modulate the swelling of the PAA network. At pHs below the pK_a of PAA (4.7), entanglements between PEG and PAA are reinforced by interpolymer hydrogen bonds, yielding IPNs with high fracture strength. At pHs above 4.7, a “pre-stressed” IPN with dramatically enhanced modulus is formed due to ionization-induced swelling of the PAA network within a static PEG network. The modulus enhancement ranged from two-fold to over 10-fold depending on the synthesis conditions used. Variation of the network parameters and swelling conditions enabled “tuning” of the hydrogels' physical properties, yielding materials with water content between 58% and 90% water, tensile strength between 2.0 MPa and 12.0 MPa, and initial Young's modulus between 1.0 MPa and 19.0 MPa. Under physiologic pH and salt concentration, these materials attain “biomimetic” values for initial Young's modulus in addition to high tensile strength and water content. As such, they are promising new candidates for artificial replacement of natural tissues such as the cornea, cartilage, and other load-bearing structures.     

基于复合左右手传输线结构的新型微带天线

基于复合左右手传输线结构的零阶谐振理论,提出了一种新型双层结构的微带天线,仿真结果表明该天线具有比单层微带天线更小的尺寸。研究了天线各结构参数对天线特性的影响,并对各参数进行了优化仿真。仿真结果表明该天线具有全向辐射特性,与传统微带天线相比,该天线具有体积小的特点。     

分离式双管板列管换热器的设计与制造

论述了双管板换热器材料选择、管板胀管槽等结构的设计、双管板检漏设计、最佳胀管压力计算等 ,以及双管板制造中内侧管子管板液压强度胀接、外侧管子管板强度焊接、双管板间空腔内和管子管板焊接接头气密性试验的要求     

双边剪智能剪切控制功能的研发与应用

在宽厚板项目中,双边剪用来剪切钢板两个纵边,以达到厂家要求的钢板宽度。本文除了介绍宽厚板双边剪的系统配置及功能特点外,主要阐述智能剪切的自动控制。本着降本增效的原则,开发一种新的主传动控制模式,优化双边剪电机剪切程序,在钢板厚度满足设定条件的前提下,固定侧与移动侧各采用一组电机驱动剪刃,并且实现主从电机智能激活切换模式,以满足生产需要。经实践证明,优化后的控制系统不仅提高了生产效率,还实现了节能降耗、安全生产的目的。     

A comparative study between chloride and calcined carbonate hydrotalcites as adsorbents for Cr(VI)

Hydrotalcite-type solids with different metal ions within the layers (M^II = Mg or Zn and M^III = Al and/or Fe) and carbonate or chloride between them have been synthesized. Chloride-LDHs and the solids obtained upon carbonate-LDHs calcination have been evaluated in the adsorptive removal of Cr(VI) from aqueous solutions. All the adsorption tests were carried out at 30 °C following two different stirring conditions: a) using a thermostatic bath with mechanical stirring at a speed of 52 rpm or b) in a sonicator bath under ultrasound waves. It was observed that no significant difference in the amount of adsorbed chromate is produced in both cases but the time spent to reach the equilibrium is much lower when the adsorbent/adsorbate mixture is submitted to ultrasounds. In all experiments L-type adsorption isotherms were obtained. The results show that chloride hydrotalcites are better adsorbents than calcined CO₃-hydrotalcites and in these last ones their adsorption capacity increases with increasing the surface area: MgAlFe > MgAl > MgFe > ZnAl.     

汽车修补涂料色母用分散剂的选用

通过对树脂、颜料、分散剂和混合溶剂的选择和定量,合成了通用色母。用指研法检验色母的分散稳定性,用倾流法或指擦法检验颜料的流动性,介绍了影响色母分散稳定性和颜料流动性的因素和原理,着重讨论了汽车修补涂料色母的单色浆微脂技术中分散剂的复配分散。