Co-Mo-K催化剂上COS、HCN转化率的热力学分析

利用热力学基础数据和相关软件对Co-Mo-K催化剂上COS、HCN加氢和水解反应进行了热力学计算。在热力学上,COS、HCN加氢和水解反应在耐硫变换条件下均为自发过程。计算结果表明在Co-Mo-K耐硫变换条件下COS、HCN主要发生的是水解反应,该结果与工业经验数据基本一致,可以作为工业实际借鉴。     

Propylene epoxidation in a microreactor with electric heating

Gas phase propylene epoxidation on gold catalysts has attracted wide attention from industry and academia due to its high selectivity. However, it suffers from low propylene conversion and rapid catalyst deactivation. Experiments showed that propylene conversion could be increased by raising H₂, O₂, or C₃H₆ concentration in the feed, but the feed compositions were within the explosion limit. It was also shown that the activity of the used catalyst could be fully recovered, but the regeneration temperature was 280 °C, much higher than that for reaction. Therefore a microchannel reactor was devised to suppress explosion and was constructed with Fecralloy, to raise the temperature rapidly for catalyst regeneration by electric heating. In two minutes the temperature of the reactor could be raised from 50 to 300 °C. Catalysts were coated on the alloy belt by dip coating, and the performance of the reactor was evaluated under different operating conditions. Results showed that in the microreactor the overall reaction rate was controlled mainly by the intrinsic reaction rate, and also influenced by film diffusion to a certain extent. The deactivated catalyst was regenerated in the microchannel reactor and the activity was fully recovered.     

浅谈国内外钒催化剂的质量差异

从化学组分、强度、活性、物相结构、孔容积及孔径分布等方面，对国产S101-2H、S108-1H钒催化剂和进口LP120、LP110钒催化剂进行剖析、对比。结果表明，国产催化剂强度比进口催化剂低30％左右；国产催化剂测定活性与进口催化剂相近，但实际使用活性明显劣于进口催化剂；进口催化剂载体中存在方英石、硫酸铝钾相，而国产催化剂没有；进口催化剂孔径分布较宽，主要孔径分布在0．50～1．50μm，而国产催化剂孔径分布较窄，主要孔径分布在0．060～0．30μm，不利于反应气体在催化剂内部的扩散。鉴此，建议采用高温煅烧载体，降低其有机物含量；优化配方，填加无机粘结剂；改进成型设备等措施，提高催化剂的强度和活性。     

Synthesis of Biodiesel from Soybean Oil using Heterogeneous KF/ZnO Catalyst

Biodiesel was produced by transesterification of soybean oil with methanol using ZnO loaded with KF as a solid base catalyst. It was found that the catalyst with 15 wt.% KF loading and calcined at 873 K showed the optimum activity. XRD, IR and Hammett indicator method were employed for the catalyst characterization. The results showed the activity of the catalysts was correlated with their basicity. The influence of various reaction variables on the conversion was also discussed.     

Liquid-phase stereoselective thymol hydrogenation over supported nickel catalysts

The stereoselective hydrogenation of thymol was studied in liquid phase over several nickel catalysts, modified by coimpregnation of inorganic compounds containing chlorine. The total activity of all catalysts studied was decreased and was on the same order of magnitude, indicating that chlorine even after reduction remains on the surface and is responsible for the poisoning effects. Such blocking of accessible sites results in similar reaction rates for the catalysts studied. Selectivity and stereoselectivity to menthols and menthones changed significantly. The modifiers could influence the rate of keto-enol transformations, which is thought to be the key selectivity and stereoselectivity governing step.     

Coking kinetics of a Cr2O3/Al2O3 catalyst during 1-butene dehydrogenation: Effect of H2 partial pressure

The influence has been studied of the partial pressure of hydrogen (0–30 kPa) upon the coking rate of a Cr₂O₃/Al₂O₃ commercial catalyst during 1-butene dehydrogenation. Coke deposition has been analysed using a monolayer-multilayer reversible coke growth model (MMRC model). This model provides good fits to the experimental data, within the range of partial pressure of H₂ studied, and allows us to estimate the main kinetic parameters involved in the coking-deactivation process. The results obtained reveal a dual effect of hydrogen: competition against 1-butene for the active sites and the removal of coke precursors from the catalyst surface. Bom effects diminish the coking rate as the H₂ partial pressure is increased.     

A203型低温氨合成催化剂使用小结

对Ａ２０３型低温氨合成催化剂的使用进行总结，介绍了该催化剂的装填，升温还原情况及使用效果。     

我国二氧化硫氧化制硫酸的钒催化剂现状和展望

从钒催化剂的生产、市场、开发、质量等方面分析我国二氧化硫氧化制硫酸催化剂的现状，指出我国钒催化剂与国外产品存在的差距和原因，提出发展钒催化剂的对策。     

钨锗酸的催化脱水反应

报道了钨锗酸对醇脱水成醚或成烯的催化反应。     

Kinetic modelling of the catalytic conversion of synthesis gas

A kinetic study for the one-step conversion of synthesis gas to gasoline on a ZnO–Cr₂O₃–ZSM-5 catalyst is described. On this catalyst, three reactions are involved in the overall transformation of synthesis gas: the methanol synthesis, the conversion of methanol to hydrocarbons and the water–gas shift reaction. Under the operating conditions selected for the study, it was found that the water–gas shift was at equilibrium and the methanol was completely converted to hydrocarbons. Consequently, it was postulated that the kinetics of the limiting reaction step, the methanol synthesis on the ZnO–Cr₂O₃ component, was the one that controls the overall reaction rate. Three kinetic model equations describing the rate of synthesis gas conversion on the bifunctional catalyst, were considered to fit the data of the experimental runs performed in a Berty well-mixed reactor. Those equations were derived under very special conditions where the methanol decomposition term could be neglected. It was also observed that in the kinetic equations a term involving the fugacity of CO₂ was required to predict the rate properly. The catalyst deactivation was also taken into account in the analysis.