周期性脉冲流体对滴流床反应器性能的影响

用铜铬催化剂催化的过氧化氢分解反应作为液体限制反应的例子来研究周期性脉冲流体对滴流床反应器性能的影响.初步研究表明:当催化剂非完全润湿时,周期性脉冲流体能够提高反应器的性能;当催化剂完全润湿时,周期性脉冲流体不能提高反应器的性能,甚至还会产生不利影响.     

铅冷快增殖堆物理和热工水力研究

对25MW电功率铅冷快增殖堆堆芯进行了物理和热工水力概算，并将计算结果与相同功率的钠冷快增殖堆的结果进行了分析比较。从初步概算的结果来看，铅冷快增殖堆是一种安全可行的快增殖堆堆型。     

ATHLET 程序及其在低温供热堆中的应用

ATHLET 程序是德国核设施安全评审中心GRS开发的一个重要的反应堆热工水力学分析程序.它可分析除堆芯熔化事故之外的其他设计基准事故,可应用于美欧传统和先进的压水堆和沸水堆,原苏联设计的压水堆(VVER)和石墨水冷堆(RBMK),以及加拿大的CANDU堆等反应堆系统的热工分析.介绍了微机版ATHLET程序,并用它对5 MW低温供热堆自然循环稳态运行工况进行了计算,结果和试验数据符合很好.     

Flow Simulation and Optimization of Plasma Reactors for Coal Gasification

This paper reports a 3-d numerical simulation system to analyze the complicated flow in plasma reactors for coal gasification, which involve complex chemical reaction, two-phase flow and plasma effect. On the basis of analytic results, the distribution of the density, tempera-ture and components‘ concentration are obtained and a different plasma reactor configuration is proposed to optimize the flow parameters. The numerical simulation results show an improved conversion ratio of the coal gasification. Different kinds of chemical reaction models are used to simulate the complex flow inside the reactor. It can be concluded that the numerical simulation system can be very useful for the design and optimization of the plasma reactor.     

滴流床设计放大中的重要参数及其数学模型

讨论了在滴流床放大过程中必须加以考虑的重要物理和化学因素以及这些因素对设计放大的影响．介绍了确定这些参数的原理和方法，推荐了用于计算这些参数的关系式，列举了用于不同反应系统的数学模型，比较了模型预测值与实验值．     

高流速双室床节水效果评价

高流速双室床(HDCB)是我国自主开发的一项水处理新技术。陕西某热电厂1年多的运行结果表明,其自用水率仅为3.2%,远低于反渗透(33%)及其他离子交换技术(10%)。HDCB自用水率低是由其结构及运行特性决定的,它具有周期制水量大,再生步骤少,再生过程用水量少,大反洗(清洗)次数少等特性,是目前化学水处理技术中节水效果最好的一种技术。     

冷床升降横梁的定位及链条调整机构改进

针对冷床频繁出现的故障情况，分析链条脱落、卡死及拉断的原因、增设升降横梁定位装置，改进链条调整装置，消除故障。     

特殊场合下的温度测量技术

对于测量条件恶劣，不能用常规传感器实现的特殊场合，如高温强腐蚀性介质、真空、高温熔体及核辐射条件下的温度测量，必须开发特种专用传感器。本文阐述了钨铼热电偶等特种温度传感器的特点、性能及应用，并着重探讨了当前测温领域热点问题。铝液、铜液及熔盐等高温溶体连续测温；高温渗碳、真空粉末治金烧结炉(气)等强还原性气氛下的温度测量：流化床等流动粉体等高温强磨损条件下的温度测量技术等。实践证明，新开发的特殊场合下专用温度传感器，不仅与国际接轨，替代进口产品，而且还可以打入国际市场。     

烧结料层厚度检测仪在生产中的应用

攀钢炼铁厂研制开发的烧结料层厚度监测仪在生产中应用后，促进了该厂烧结生产操作的稳定与进步，取得了产质量提高的良好效果。     

Mineralogy of clean coal combustion by-products

Coal combustion technologies are changing in order to burn coal more cleanly. Many “clean combustion“ and postcombustion technologies are developed to remove SO2 and NOx gases, particulate matter during combustion, or from the flue gases leaving the furnace. This paper focuses on three types of fly ash (flue gas desulfurization (FGD) residuals, atmospheric fluidized bed combustion (AFBC) residuals and sorbent duct injection (SDI) residuals) which produced by “the clean combustion“ and postcombustion technologies. The residuals formed by FGD are PCFA (pulverized coal fly ash) grains entrained with reacted and unreacted sorbent and have lower bulk densities than PCFA grains because it contains higher concentrations of calcium and sulfur, and lower concentrations of silicon, aluminum and iron than PCFAs. AFBC residuals consist of spent bed which is a heterogeneous mixture of coarse-grained bed material and irregularly shaped, unfused, spherical PCFAs. The main crystalline phases in AFBC residuals are anhydrite (reacted sorbent), quartz and lime (unreacted sobent), calcite, hematite, periclase, magnetite and feldspars.The residuals produced by SDI contained 65%-70% PCFA with the larger sizes material being irregularly shaped, fused or roughedged. The reaction products of sorbent (portlandite and lime) included calcium sulfate (anhydrite) and calcium sulfate. The chemical properties of these residuals are similar to those of high calcium PCFAs because of the high alkalinity and high pH of these residuals.