Properties and Performance of Cation-Doped Ceria Electrolyte Materials in Solid Oxide Fuel Cell Applications

Cation-doped CeO₂ electrolyte has been evaluated in single-cell and short-stack tests in solid oxide fuel cell environments and applications. These results, along with conductivity measurements, indicate that an ionic transference number of ∼0.75 can be expected at 800°C. Single cells have shown a power density >350 mW/cm². Multicell stacks have demonstrated a peak performance of >100 mW/cm² at 700°C using metallic separators.     

时序电路逻辑初始化问题研究

讨论同步时序电路初始化问题,提出了一种基于电路存储元件逻辑定级和可控性分析的同步时序电路逻辑初始化方法。同时也给出了针对ISCAS89电路的一些实验结果。     

DLL23XA双侧向测井仪的研制

以往双侧向测井仪动态范围小，测量精度低，为此开发了DLL23XA双侧向测井仪。该仪器主要单元采用厚膜电路，稳定性、一致性好；深、浅屏流源采用可变功率控制，提高了仪器的动态范围。仪器采用3506P例进行数据传输，可方便地配接各种地面系统。     

X441对数放大器的原理及其应用

本文主要介绍X441单片对数放大器的基本原理和应用,并列举了一些具体应用电路。     

外焊缝自动跟踪系统

介绍了外焊缝自动跟踪系统的组成及工作原理，简述了传动部分ＧＴＲ－ＰＷＭ调速系统，给出了系统的硬件电路。该跟踪器具有结构简单，体积小，性能稳定等特点，在生产线上获得了成功的应用。     

一种提高微电路外壳使用可靠性的方法

简要分析了白瓷双列直插外壳的失效模式和失效机理，并进行了模拟实验，通过对实验结果的分析，提出对成品微电路进行二次电镀能够提高其外壳的使用可靠性。     

混合集成电路激光功能调值技术

本文提出了激光功能微调技术在高精度混合集成电路上的应用，讨论了关键技术问题，并以实例具体说明。该技术的应用为研制高精度混合集成电路开辟了新途径。     

Microscopic fatigue processes in a plain-weave glass-fibre composite

This paper focuses on the microscopic damage and progressive failure of a composite reinforced by plain-weave glass cloth under tensile fatigue loading. The fatigue process was divided into three stages like that of multi-directional laminates. It was found that the internal damage at each stage (matrix cracks, debonds in the weft, successive debonds in the warp and ‘metadelaminations’ between warps and wefts) occurred near the cross-over point of the fabric. The modulus decay mechanism was explained by considering the progression of this internal damage. From the end of the first stage to the beginning of the middle stage, a characteristic damage state (CDS) (called a ‘meta-CDS’) was observed. It was found that woven composites have a unit area of damage accumulation (called a ‘unit cell’) and the damage of each unit cell and its distribution control the total fatigue damage of the material.     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation