Analytical modeling and experimental study of tensile strength of asphalt concrete composite at low temperatures

In this study, analytical modeling of the tensile strength of hot-mix asphalt (HMA) mixtures at low temperatures was developed. To do this, HMA mixtures were treated as a two-phase composite material with aggregates (coarse and fine) dispersed in an asphalt mastic matrix. A two-phase composite model, which was similar to Papanicolaou and Bakos's [J. Reinforced Plast. Compos. 11 (1992) 104] model with a particle embedded in an infinite matrix, was proposed. Unlike Papanicolaou and Bakos's model, an axial stress was introduced to the fiber end to consider the load transferred from the asphalt mastic the aggregate. Efforts were also made to consider the effect of aggregate gradation, asphalt mastic degradation, and interfacial damage between the aggregates and asphalt mastic matrix on the tensile strength of the HMA mixtures. Experimental investigations were conducted to validate the developed theoretical relations. A reasonable agreement was found between the predicted tensile strength and the experimental results at low temperatures. Parameters affecting the tensile strength of asphalt mixtures were discussed based on the calculated results.     

Performance of a Yeast-mediated Biological Fuel Cell

Saccharomyces cerevisiae present in common Baker’s yeast was used in a microbial fuel cell in which glucose was the carbon source. Methylene blue was used as the electronophore in the anode compartment, while potassium ferricyanide and methylene blue were tested as electron acceptors in the cathode compartment. Microbes in a mediator-free environment were used as the control. The experiment was performed in both open and closed circuit configurations under different loads ranging from 100 kΩ to 400Ω. The eukaryotic S. cerevisiae-based fuel cell showed improved performance when methylene blue and ferricyanide were used as electron mediators, rendering a maximum power generation of 146.71±7.7 mW/m³. The fuel cell generated a maximum open circuit voltage of 383.6±1.5 mV and recorded a maximum efficiency of 28±1.8 % under 100 kΩ of external load.     

钛镍形状记忆合金的研究进展

从应用角度简要介绍了钛镍合金的研究和应用状况，简明地评述了它的物理冶金基础、热机械行为和力学模型的研究情况．     

Fe-substituted (La,Sr)TiO3 as potential electrodes for symmetrical fuel cells (SFCs)

In the work presented herein, the potential use of La₄Sr₈Ti_12−xFe_xO_38−δ (LSTF) materials as electrodes for a new concept of solid oxide fuel cells, symmetrical fuel cells (SFCs), is considered. Such fuel cells use simultaneously the same material as anode and cathode, which notably simplifies the assembly and further maintenance of the cells. Therefore, we search for materials showing high conductivity in a wide range of oxygen partial pressures in addition to certain degree of catalytic activity for the oxidation of the fuel and reduction of the oxidant, respectively. The preliminary electrochemical experiments performed reveal that the overall conductivity increases notably upon Fe substitution, being the main contribution electronic n-type. The fuel cell tests indicate that LSTF composites with YSZ and CeO₂ perform reasonably well under H₂ conditions, although the performance in methane is rather modest and require further optimisation.     

亚齐示范屋与生态技术

亚齐示范屋是在传承印度尼西亚当地住宅传统的基础上，海啸灾区重建的示范性建筑。从当地传统的传承、设计理念及生态技术方面对该示范屋进行了分析、研究，结合我国的情况得出我国生态建筑的发展策略。     

Modeling and performance analysis of IP access interface in optical transmission networks with packet switching

The article analyzes the influence of the Internet Protocol (IP) access interface on the packet loss probability and delay times in the optical packet switched network. The network and node model have been proposed, and the structure of the IP access interface, including assembler and holder, have been included in the analysis. It has been shown that the increase of the maximum optical packet sizes, as well as use of the holding feature as contention resolution mechanism, decrease the packet loss probability, but introduce delays at the optical network access points. Modeling and analysis were based on the discrete event simulation assuming self-similar traffic sources. IP packet lengths were modeled using empirical data. This work has been conducted while the author was affiliated with the Telecommunication Laboratory, Swiss Federal Institute of Technology (EPFL-STI-ITOP-TCOM), Lausanne, Switzerland     

用热分析法研究硝化棉的熔化过程

用ＭＤＳＣ，显微镜温台熔点测定仪和固体原位反应池／快速扫描傅立叶变换红外光谱联用装置考察了硝化棉的熔化过程。ＭＤＳＣ曲线表明吸热过程是可逆的，它系由ＮＣ和部分分解凝聚相产物的混合物的固液相变所引起。由ＮＣ的ＭＤＳＣ曲线得到的熔点，熔化含，熔化熵，分解含和分解反应热温熵分别为４７６．８４Ｋ，２０５．６Ｊ．ｇ＾－１，０．４３１２Ｊ．ｇ＾－１．Ｋ＾－１，－２４７５．０Ｊ．ｇ＾－１，－５．２４２Ｊ．ｇ＾－     

On modeling the design of cellular manufacturing systems

A new optimization model is discussed for the design of cellular manufacturing systems. It is based on an integer programming formulation that updates some other models by eliminating redundant machine assignment and cost coefficients dependent on cell configuration. To reduce computational burdens, a simplified integer programming model and a decomposition algorithm are proposed. Several computer solutions were performed to evaluate the performance of the new model. The computational results are discussed.     

A methodology for investigating effects of cell size on operational flexibility in flexible manufacturing systems

There are two aspects to cell formation in flexible manufacturing systems, cell sizing or deciding on the optimum number of machines to be allocated to each cell, and then allocation of specific machines to each cell. Although the latter problem has been investigated extensively there is a paucity of published work on the former. This paper discusses the effects of cell sizing on operational flexibility.Operational flexibility is that aspect of flexibility that enables manufacturing systems to respond with speed and efficiency to changes in the manufacturing environment while maintaining an effective level of control.     

Effect of temperature on recombinant protein production using the Bm5/Bm5.NPV expression system

A series of experiments have been conducted using a recombinant baculovirus/insect cell expression system (Bm5/Bm5.NPV.CAT) to establish the optimum temperature for both cell growth and virus infection. Bm5 cell growth was found to be limited at temperatures below 22°C and ceased completely at temperatures above 34°C. In the range between 24 and 28°C, final cell densities always reached 96% of the highest achievable viable cell density. The shortest population doubling time was obtained at 28°C. Overall, a consistent increase in metabolism with increasing temperatures was observed. During the infection/viral replication phase, an increase in the temperature from 25 to 31°C resulted in a faster decrease in viable cell density and an earlier production of chloramphenicol acetyltransferase (CAT). Furthermore, protein yield at temperatures above 28°C was significantly reduced. Overall, the best temperature for the infection phase for the Bm5/Bm5.NPV expression system was found to be 25°C when the cells are cultured in serum free media.