Comparison of Displacement and Mixing Diffusers

In order to cumpare the peformance of different supply diffuers of ventilation air, the airflow passern, temperature stratifiation and contaminant dispersion in a furnitured office ventilated by three kinds of air diffuer were numerically investigated. The air diffuers studied in this paper are a quarter-cylinder displacement diffuer on the floor and mixing diffuers (linear and vortex diffuers) on the ceiling. The heat sources in the of-fice are considered to be 50% convective and 50% radiative. The k-? two-equatwn model of turbulence is employed to predict the turbulent diffusion. The results show that the displacement diffuser provides a rather uniform flow field with low velocify in most areas, and the vertical temperature difference from floor to ceiling is as high as 6 K. With the linear diffuser, the air velociry is high, and the temperature is uniform both horizontally and vertically. The air velocity generated by the vortex diffuser is moderate. The distributions of the temperature and the contaminant are rather uniform.     

Effective lightning protection schemes for distribution line

The causes of lightning outage are subdivided into direct lightning strokes and induced lightning strokes, which are identified by the characteristics of the lightning overvoltage. In the past, lightning protection devices were directed mainly toward the latter, and attention has been focused on the installation of lightning protection devices, ground wires, and reinforcement of insulators. However, lightning outages continue to occur. Thus it is extremely important to clarify the fault characteristics of lightning surges and to study the effectiveness of various lightning protection devices by considering both direct lightning stroke and induced lightning stroke in order to prevent lightning outage in the future. In this research, the electromagnetic transients program (EMTP) has been applied to the direct lightning stroke, and the induced lightning outage analysis program for multiple conductor systems has been applied to the induced lightning stroke to study the effectiveness of lightning protection devices provided by combination of various lightning protection devices. The most effective lightning protection schemes are analyzed and evaluated based on verification tests on the full scale models as well as economic considerations.     

Thermal design method of bayonet-tube evaporators and condensers

The paper describes an effectiveness-NTU design method of bayonet-tube evaporators and condensers. Including the effect of the wall superheat on the shell-side film coefficient, and using an energy balance on the tube, differential equations for the steady-state fluid temperatures are formulated. Because of the nonlinear nature of the governing equations, the fourth-order Runge-Kutta method is employed to the solution of the finite difference equations. The results are iterated with the combination of integration techniques. An upper bound to the numerical error being ±5% the fluid temperature distribution as well as the exchanger effectiveness are determined, and presented as a function of the Hurd number, the number of heat transfer units and the flow arrangement. For flow entering through the inner tube, the temperature distribution displays the occurrence of a minimum at a point other than the tube-tip of the exchanger. In an extension of the analysis, an effort is made to illustrate the deviation of the results obtained by uniform film coefficient from the present study, and the differences are outlined.     

Strain analysis of moving objects using a Fourier transform grid method

There is no good method to measure the shape and the strain distributions of a structure changing with time. We have previously proposed the Fourier transform grid method (FTGM) to measure the three-dimensional shape and surface strain distributions of stationary objects by analysing the two-dimensional grating images recorded with two cameras. In the stereoscopic method, it is very important to determine the accurate geometric parameters of the camera system. In this paper, the positions and the directions of cameras are accurately determined using the FTGM applied to images of a reference object on which a two-dimensional grating is drawn. Applications for analysing shape and strain distributions of vibrating rubber plates and a moving human skin are shown.     

一种简便的评定引战配合效率方法

在导弹近炸引信起爆延时具有随机性基础上，本文建立了一种用延时及其数学特征表示的评定引战配合效率的简便方法，并对有关应用问题进行了讨论。     

压裂泵往复密封性能及机理研究

根据流体动压润滑理论，对压裂泵柱塞密封摩擦副的润滑机理进行了理论分析。在排出和吸入行程，柱塞密封摩擦副均能满足流体动压润滑的条件，即在柱塞与密封界面上能形成并保持一定厚度的油膜润滑密封，从而达到减小摩擦提高寿命的目的；建立了摩擦界面油膜厚度和泄漏量的计算公式。利用有限元法理论，对密封圈的压力沿轴向的分布规律、泄漏量与压力变化关系进行了模拟计算。对往复密封圈沿轴向压力分布、泄漏量随压力变化进行了测试；试验结果表明，建立的计算模型具有较高的计算精度，揭示了压裂泵的密封机理。     

Comparative analysis of urban reflectance and surface temperature

Urban environmental conditions are strongly dependent on the biophysical properties and radiant thermal field of the land cover elements in the urban mosaic. Observations of urban reflectance and surface temperature provide valuable constraints on the physical properties that are determinants of mass and energy fluxes in the urban environment. Consistencies in the covariation of surface temperature with reflectance properties can be parameterized to represent characteristics of the surface energy flux associated with different land covers and physical conditions. Linear mixture models can accurately represent Landsat ETM+ reflectances as fractions of generic spectral endmembers that correspond to land surface materials with distinct physical properties. Modeling heterogeneous land cover as mixtures of rock and/or soil Substrate, Vegetation and non-reflective Dark surface (SVD) generic endmembers makes it possible to quantify the dependence of aggregate surface temperature on the relative abundance of each physical component of the land cover, thereby distinguishing the effects of vegetation abundance, soil exposure, albedo and shadowing. Comparing these covariations in a wide variety of urban settings and physical environments provides a more robust indication of the global variability in these parameter spaces than could be inferred from a single study area. A comparative analysis of 24 urban areas and their non-urban peripheries illustrates the variability in the urban thermal fields and its dependence on biophysical land surface components. Contrary to expectation, moderate resolution intra-urban variations in surface temperature are generally as large as regional surface heat island signatures in these urban areas. Many of the non-temperate urban areas did not have surface heat island signatures at all. However, the multivariate distributions of surface temperature and generic endmember fractions reveal consistent patterns of thermal fraction covariation resulting from land cover characteristics. The Thermal-Vegetation (TV) fraction space illustrates the considerable variability in the well-known inverse correlation between surface temperature and vegetation fraction at moderate (< 100 m) spatial resolutions. The Thermal-Substrate (TS) fraction space reveals energetic thresholds where competing effects of albedo, illumination and soil moisture determine the covariation of maximum and minimum temperature with illuminated substrate fraction. The dark surface endmember fraction represents a fundamental ambiguity in the radiance signal because it can correspond to either absorptive (e.g. low albedo asphalt), transmissive (e.g. deep clear water) or shadowed (e.g. tree canopy shadow) surfaces. However, in areas where dark surface composition can be inferred from spatial context, the different responses of these surfaces may still allow them to be distinguished in the thermal fraction space.     

高速钢高温形变诱发析出的研究

本文探讨了高速钢在高温形变过程中碳化物析出的行为及奥氏体组织状态对析出的影响。用透射电镜和扫描电镜分析了不同热处理状态奥氏体的组织结构,分析了高温形变过程中碳化物析出的部位,颗粒尺寸及形态。试验表明, 碳化物主要在奥氏体的缺陷处呈点状和点列状析出,大小为20mμ。处于回复状态的奥氏体缺陷诱发碳化物析出,析出碳化物钉札缺陷阻止再结晶进行。当再结晶驱动力较大时,由于动态再结晶充分发展,使缺陷大量消除,碳化物析出显著地减少。     

Multistage Zeolite Drying for Energy-Efficient Drying

This work discusses the potential of three multistage zeolite drying systems (counter-, co-, and cross-current) with a varying number of stages. The evaluation showed that for 2-4 stages with heat recovery the efficiency of the systems ranges between 80 and 90%. Additionally, by introducing a compressor, the latent heat in the exhaust air from the regenerator is recovered and used to heat the inlet air for an additional drying stage. As a result, for the counter-current drying system and compressor pressure 1.5-2 bar, a maximum energy efficiency of 120% is achieved, which results in halving the energy consumption compared to conventional drying systems.