Φ10007/00有压三产品重介旋流器结构参数优选与分选效果

辛置选煤厂针对原煤煤质变化后的特点 ,采用有压给料三产品重介旋流器为核心的高效选煤工艺系统分选 5 0～ 0mm原煤 ;对旋流器一段及二段中心管的直径和插入深度、二段底流口的直径等进行了优化调整 ,同时调整了介质泵的工作频率及悬浮液密度等参数 ,取得了分选效率高、产品质量稳定等显著效果     

一次多级离心泵运行故障处理及分析

简要介绍了实际生产中多级离心泵存在的问题,并分析了故障原因和处理措施。     

一种新型非对称齿形的齿轮泵

通过对新型非对称齿形齿轮泵与对称齿形齿轮泵的分析比较，指出了提高齿轮泵工作效率之途径。     

稀磷酸澄清槽泥浆泵改用单螺杆泵的实践

磷酸生产中输送稀磷酸澄清槽淤渣的泥浆泵，各厂的运行情况都不够理想。介绍了三种类型泥浆泵的运行情况，针对淤渣中会出现块结垢物影响泥浆泵长期运行，在单螺杆泵进料腔内设置破碎送料器后，取得了较理想的效果，从而提高了磷酸装置的运转率和磷得率。     

液氯离心泵的气蚀与防治

分析了影响液氯离心泵气蚀的两种参数：允许吸上真空度、气蚀余量。提出了泵气蚀的防治措施：提高离心泵基础设计质量，在实际使用中应采用高分子聚合材料涂覆，并进行补焊、补气。     

A three-dimensional model for suspension-to-membrane-wall heat transfer in circulating fluidized beds

A three-dimensional model is proposed for both furnace-side and wall-side heat transfer in circulating fluidized beds with membrane walls. Following previous publications (Int. J. Heat Mass Transfer (2003a, b)), a core-annulus flow structure is employed in the model, with consideration of the membrane wall influence on bed hydrodynamics. The model couples radiation, conduction and convection on the furnace side to conduction and convection on the wall side. Radiation in the wall layer is simulated by the moment method. A finite-element method is employed to solve the set of non-linear, partial differential equations. The solution is demonstrated for a typical example. The model gives predictions of suspension-to-wall heat transfer which show satisfactory agreement with published experimental data.     

A novel shaft-less double suction mini pump

A novel double suction shaft-less mini pump was developed for heat control of small energy systems in this study.The mini pump impeller with an exit diameter of 40 mm was combined with the motor rotor supported by the hybrid dynamic bearing.The specific speed of the pump was 125 min-1 m3 min-1 m.The hydraulic performance of the pump was investigated experimen-tally under four rotational speeds.From the test results,it was recognized that the pump could provide a flow discharge of 5 L/min and head of 1.5 m,w...     

Air-source heat pump coupled with economized vapor injection scroll compressor and ejector:Design and experimental research

Ejector can utilize high pressure energy from liquid mechanism,it can be used in heat pump system coupled with economized vapor injection(EVI)scroll compressor.When running under low temperature conditions,the performance of the EVI system with ejector can be improved further.In this paper,the design method of the heat pump system with ejector is presented,and the process for designing the heat pump with ejector(EVIe)was summarized.One prototype heat pump was designed under the condition of the evaporation ...     

太阳能溴化锂吸收式制冷系统吸收特性的研究

太阳能溴化锂吸收式制冷系统的吸收器采用传热、传质分离装置,利用预冷器预先冷却和喷淋吸收的方法完成对传热、传质的分离。通过建立吸收器的计算模型,分析冷冻水出口温度、冷却水进口温度、热水温度、喷淋温度、喷淋密度等因素对传热、传质的影响。利用传热、传质分离方法,使系统的吸收特性得到强化,从而使系统获得较高的性能系数。     

Transitions from solid to liquid in isotactic polystyrene studied by thermal analysis and X-ray scattering

A three-phase model, comprising mobile amorphous fraction (MAF), rigid amorphous fraction (RAF) and crystalline fraction (C), has been applied to interpret the thermal transitions and structure of cold-crystallized isotactic polystyrene (iPS) from below the glass transition temperature, T_g, to above the melting point. Quenched amorphous iPS films were isothermally crystallized at different temperatures for 12 h. The fraction of crystalline phase, ?_c, was measured by differential scanning calorimetry (DSC), wide angle X-ray scattering and Fourier Transform infrared spectroscopy. The fraction of the mobile amorphous phase, ?_MAF, was obtained from the heat capacity increment at the glass transition temperature. In the three-phase model, the fraction of the rigid amorphous phase, ?_RAF, was found from 1−?_MAF−?_c. Specific heat capacity measurements by standard DSC confirm that the experimental baseline heat capacity conforms to a three-phase model for temperatures ranging from below T_g, up to the relaxation of RAF. The relaxation of RAF appears as a sigmoidal change in heat capacity accompanied by excess enthalpy, in which solid-like RAF is converted to an identical amount of liquid-like MAF.At temperatures above the relaxation of RAF, either one or two major crystal melting endotherms are observed in standard DSC, dependent upon crystallization temperature. However, using quasi-isothermal temperature modulated DSC, we always observed two reversing melting endotherms. The effects of annealing on iPS structure during the quasi-isothermal measurement were assessed using small angle X-ray scattering (SAXS). Combining the DSC and SAXS results, a model for the melting of iPS lamellae at low heating rates is presented.