Reliability and performance analysis of time – space – time switching networks with multiple separated space switches

Since electronic switching systems usually require very strict reliability requirements as well as good performance objectives, we need to jointly analyse the performance and reliability of switching systems. In this paper, we compare conventional time–space–time switches with single space switches with those with multiple separated space switches, from the viewpoints of reliability and performance. We consider time–space–time switching networks which consist of N incoming time switches, i.e. one NxN space switch, two (N/2)x(N/2) space switches, and four (N/4)x(N/4) space switches. We introduce a Markov reliability model to study the effect of failures and analyse the reliability and performance of three different types of switching networks in terms of average blocking probability and the mean time to unreliable operation, as we vary the offered traffic. As a result, T–S–T switching networks with multiple separated space switches exhibit better performance and reliability than those with single space switches.     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

Thermal design method of bayonet-tube evaporators and condensers

The paper describes an effectiveness-NTU design method of bayonet-tube evaporators and condensers. Including the effect of the wall superheat on the shell-side film coefficient, and using an energy balance on the tube, differential equations for the steady-state fluid temperatures are formulated. Because of the nonlinear nature of the governing equations, the fourth-order Runge-Kutta method is employed to the solution of the finite difference equations. The results are iterated with the combination of integration techniques. An upper bound to the numerical error being ±5% the fluid temperature distribution as well as the exchanger effectiveness are determined, and presented as a function of the Hurd number, the number of heat transfer units and the flow arrangement. For flow entering through the inner tube, the temperature distribution displays the occurrence of a minimum at a point other than the tube-tip of the exchanger. In an extension of the analysis, an effort is made to illustrate the deviation of the results obtained by uniform film coefficient from the present study, and the differences are outlined.     

伺服元件的生产应用及发展趋势

本文概括地介绍了我国自70年代以来伺服元件的生产发展状况、元件的性能特点和应用情况，并分析了今后发展的趋势。     

Second-law-based thermodynamic analysis of two-stage and mechanical-subcooling refrigeration cycles

Thermodynamic analysis of HFC-134a vapor-compression refrigeration cycles is investigated by both the first and second laws of thermodynamics. Second-law analysis is carried out for both two-stage and mechanical-subcooling refrigeration cycles. The analysis is performed on each of the system components to determine their individual contribution to the overall system irreversible losses. It is found that most of the losses are due to a low compressor efficiency. Irreversibilities of expansion valves and condenser are also significant. In addition, it is shown that the optimum inter-stage pressure for two-stage and mechanical-subcooling refrigeration systems is very close to the saturation pressure corresponding to the arithmetic mean of the refrigerant condensation and evaporation temperatures. These results are compared with the existing practice in the industry. Furthermore, theoretical results of a two-stage refrigeration system performance are also compared with experimental values for a CFC-22 system.     

Impact of uncertainties on estimations of heat pump cycle performance

Sensitivity analysis is used to show how uncertainties in basic factors, such as heat transfer, pressure drop, compressor efficiency, and thermophysical properties, influence the result of heat pump cycle performance estimations. By comparing the results of this analysis with uncertainty levels of estimations and experimental determinations, it is established to what extent improvements in accuracy are needed. The investigation was carried out for several different applications and, as working fluids, both pure substances and non-azeotropic mixtures were examined. It was found that evaporation heat transfer and compressor efficiency are two areas where improvements are needed. It is also shown that estimates using very accurate, substance-specific, equations of state differ from those using more general types by up to 1 % for COP and 2% for capacity.     

Comparative analysis of urban reflectance and surface temperature

Urban environmental conditions are strongly dependent on the biophysical properties and radiant thermal field of the land cover elements in the urban mosaic. Observations of urban reflectance and surface temperature provide valuable constraints on the physical properties that are determinants of mass and energy fluxes in the urban environment. Consistencies in the covariation of surface temperature with reflectance properties can be parameterized to represent characteristics of the surface energy flux associated with different land covers and physical conditions. Linear mixture models can accurately represent Landsat ETM+ reflectances as fractions of generic spectral endmembers that correspond to land surface materials with distinct physical properties. Modeling heterogeneous land cover as mixtures of rock and/or soil Substrate, Vegetation and non-reflective Dark surface (SVD) generic endmembers makes it possible to quantify the dependence of aggregate surface temperature on the relative abundance of each physical component of the land cover, thereby distinguishing the effects of vegetation abundance, soil exposure, albedo and shadowing. Comparing these covariations in a wide variety of urban settings and physical environments provides a more robust indication of the global variability in these parameter spaces than could be inferred from a single study area. A comparative analysis of 24 urban areas and their non-urban peripheries illustrates the variability in the urban thermal fields and its dependence on biophysical land surface components. Contrary to expectation, moderate resolution intra-urban variations in surface temperature are generally as large as regional surface heat island signatures in these urban areas. Many of the non-temperate urban areas did not have surface heat island signatures at all. However, the multivariate distributions of surface temperature and generic endmember fractions reveal consistent patterns of thermal fraction covariation resulting from land cover characteristics. The Thermal-Vegetation (TV) fraction space illustrates the considerable variability in the well-known inverse correlation between surface temperature and vegetation fraction at moderate (< 100 m) spatial resolutions. The Thermal-Substrate (TS) fraction space reveals energetic thresholds where competing effects of albedo, illumination and soil moisture determine the covariation of maximum and minimum temperature with illuminated substrate fraction. The dark surface endmember fraction represents a fundamental ambiguity in the radiance signal because it can correspond to either absorptive (e.g. low albedo asphalt), transmissive (e.g. deep clear water) or shadowed (e.g. tree canopy shadow) surfaces. However, in areas where dark surface composition can be inferred from spatial context, the different responses of these surfaces may still allow them to be distinguished in the thermal fraction space.     

气敏材料的研究进展

从气敏材料种类，制备方法，改善气敏材料缺陷的手段等方面介绍了气敏材料的研究进展，论述了气敏材料研究中的新动向，展望了它的未来发展。     

Multistage Zeolite Drying for Energy-Efficient Drying

This work discusses the potential of three multistage zeolite drying systems (counter-, co-, and cross-current) with a varying number of stages. The evaluation showed that for 2-4 stages with heat recovery the efficiency of the systems ranges between 80 and 90%. Additionally, by introducing a compressor, the latent heat in the exhaust air from the regenerator is recovered and used to heat the inlet air for an additional drying stage. As a result, for the counter-current drying system and compressor pressure 1.5-2 bar, a maximum energy efficiency of 120% is achieved, which results in halving the energy consumption compared to conventional drying systems.