In the present study, biodiesel production from the crude cotton-seed oil (CSO) and its feasibility to be used as fuel in compression ignition engine was analysed. Single-stage transesterification at molar ratio of 8:1 on crude CSO yielded 94% of cottonseed biodiesel (CBD). Gas chromatogram/mass spectrometry analysis revealed the presence of 19.5% unsaturated and 80.5% saturated esters in cotton seed biodiesel. Taguchi approach identified the stable fuel blend with oxygenate concentration. Increased oxygen concentration up to 20% were also analysed to understand the variation. Higher peak in-cylinder pressure was observed in D80CBD20 fuel blend. Diesel–biodiesel blend with oxygenate significantly affected the ignition delay and also resulted in varied exhaust gas temperature. D80CBD20nB10 showed an increase in brake thermal efficiency, whereas D80CBD20 exhibited higher brake specific energy consumption at full load. Carbon monoxide, hydrocarbon and smoke emission was found to be high in diesel with higher oxides of nitrogen in D80CBD20nB10. This experimental investigation finally revealed that, D80CBD20nB10 improved the combustion and performance characteristics with minimal emissions.
Abbreviations ASTM: American Society for Testing and Materials; BP: brake power; BSEC: brake specific energy consumption; BTE: brake thermal efficiency; CBD: cottonseed biodiesel; CI: compression ignition; CO: carbon monoxide; CO2: carbon dioxide; CSO: cottonseed oil; DEE: diethyl ether; DOE: design of experiments; EGT: exhaust gas temperature; FTIR: Fourier transform infrared spectrometry; GC/MS: gas chromatogram/mass spectrometry; HC: hydrocarbon; HRR: heat release rate; HSDI: high speed direct injection; IDI: indirect injection; KOH: potassium hydroxide; MFB: mass fraction burned; NaOH: sodium hydroxide; NMR: nuclear magnetic resonance; N2O: nitrous oxide; NO: nitric oxide; NO2: nitrogen dioxide; NOx: oxides of nitrogen; ROHR: rate of heat release; ROPR: rate of pressure rise; SOC: start of combustion; aTDC: after top dead centre; bTDC: before top dead centre 相似文献
The conversion of fatty acid methyl ester (FAME) from triglycerides using heterogeneous catalysis has gained increasing interest due to the prospect of increased yield at reduced operating costs and reaction conditions. In this paper, meso-porous hydrotalcite was used to catalyze jatropha oil into FAME with relatively higher yield at atmospheric pressure and relatively low reaction temperature. The molar ratio of methanol to oil required was relatively low and the conversion was completed within few hours of reaction time. The reaction was promoted when moderate calcination temperature was applied, the disordered structure of the catalyst was maintained, counterbalance anions was removed, and phase transitions within the oxide lattice was induced. Despite the observed deactivation during successive reaction cycles due to adsorption of residual triglycerides, the catalyst performance was restored effectively by air-re-calcination. 相似文献
In this study, two continuous processes for biodiesel production, alkali catalyzed process and solid acid catalyzed process, are discussed with the help of Aspen Plus. By comparing some economic indicators, it can be found that solid acid catalysis could be a good choice for investors in the near future. 相似文献
Algae can be a viable source for biofuel production, but the source of nitrogen used to cultivate could affect algae yields. Here, we observe how various nitrogen treatments can impact the growth and biovolume of microalga Nannochloropsis salina as well as invasion of undesired organisms. Invading organisms increase the likelihood of crashes of the desired microalgae culture. Experiments were conducted over 28 days in open aquaria in a greenhouse. We used five different nitrogen treatments; ammonium chloride (NH4Cl), ammonium hydroxide (NH4OH), sodium nitrate (NaNO3), urea (CH4N2O), and a mixture of all these sources. Highest values for Maximum Sustainable Yield (MSY), a measure of potential harvest rate based on population productivity, were observed in the urea treatment, but cell size was smaller compared to other treatments. Sodium nitrate and the mixture of nitrogen sources also had high MSY values but larger cell sizes, making them the treatments with highest total biovolume. The highest percentages of lipid by weight, but also highest densities of invading organisms were observed in the mixed treatment. Our results suggest that tradeoffs between biovolume and lipid yields as well as culture success can ultimately decide what nitrogen sources to use. 相似文献
Fuel quality, especially biodiesel, is highly dependent on its water content, and the major sources of water in the fuel relate to the transportation, production, and storage processes. In this present contribution, the multilayer perceptron artificial neural network (MLP-ANN) was applied to predict the water content of biodiesel and diesel blend in terms of temperature and composition. The proposed algorithm was trained and tested by utilizing 400 experimental data points which were extracted from the literature. Based on the results, the MLP-ANN model has great ability to estimate the water content of biodiesel and diesel blend. The R-squared (R2), root mean square error, average absolute relative deviation, and a?bsolute deviation parameters for the total data set are obtained, respectively, as 0.99784, 123919.1172, 3.3632, and 1.17%, which indicate the effective performance suggested by ANN. As the computational study is cheaper and easier than the experimental study, the developed software could be considered as an alternative for laboratory study, and the environmental effect of biodiesel and produced undesired product after biodiesel combustion which is directly related to the water content of biodiesel is estimable with the information released in this study. 相似文献
In present work, the aim of producing biodiesel from waste cooking oil was pursued by doping the cerium element into the MCM‐41 framework as catalyst with various Si/Ce molar ratio (5, 10, 25, 50, and Ce = 0). The catalytic performance and stability improved by employing the ultrasound irradiation in active phase loading step of catalyst preparation. The physicochemical characteristics of synthesized samples were investigated using various techniques as follows: Brunauer‐Emmett‐Teller (BET), X‐ray powder diffraction (XRD), Fourier transfer infrared (FTIR), energy‐dispersive X‐ray spectroscopy (EDX), transmission electron microscopy (TEM), and field emission scanning electron microscope (FESEM). The XRD patterns along with the results of FTIR and BET analysis revealed the MCM‐41 framework destruction while increasing the Ce content. The FESEM images of the nanocatalysts illustrated a well distribution and uniform morphology for the Ca/CeM (Si/Ce = 25). The particle size and size distribution of the Ca/CeM (Si/Ce = 25) were subsequently determined by TEM and FESEM images. The activity of fabricated nanocatalysts was evaluated by measuring the free acid methyl ester (FAME) content of produced biodiesel. The tests were carried out at constant operational conditions: T = 60°C, catalyst loading = 5 wt%, methanol/oil molar ratio = 9, and 6‐hour reaction time. A superior activity was observed for Ca/CeM (Si/Ce = 25) among other nanocatalysts with 96.8% conversion of triglycerides to biodiesel. The mentioned sample was utilized in five reaction cycles, and at the end of the fifth cycle, the conversion reached to 91.5% which demonstrated its significant stability. 相似文献