黄埔发电厂#6发电机转冷水系统改造

黄埔发电厂#6发电机转冷水铜离子含量超标，通过对缺陷原因进行分析，针对二级水封的特性对溢出的转冷水进行回收并利用化学凝结水处理去除溶出的铜离子，通过控制转冷水的pH值最终减缓铜管的腐蚀.     

New concept of surface modification to LiCoO2

As the continuance of our series study on LiCoO₂ surface modification, the complicated traditional surface coating method is replaced with simple addition of amorphous YPO₄ and Al₂O₃ in commercial LiCoO₂ or in commercial electrolyte based on our understanding to the improvement mechanism of surface modification. Comprehensive studies by X-ray photoelectron spectroscopy (XPS), gas chromatography and mass spectroscopy (GC–MS), inductively coupled plasma (ICP) and Fourier transformed infrared (FTIR) indicate that the products of spontaneous reaction between the additive and the LiPF₆ based electrolyte are responsible for the performance improvements.     

Evaluation of the reactivity of titanium with mould materials during casting

A methodology for evaluating the reactivity of titanium with mould materials during casting has been developed. Microhardness profiles and analysis of oxygen contamination have provided an index for evaluation of the reactivity of titanium. Microhardness profile delineates two distinct regions, one of which is characterised by a low value of hardness which is invariant with distance. The reaction products are uniformly distributed in the metal in this region. The second is characterised by a sharp decrease in microhardness with distance from the metal-mould interface. It represents a diffusion zone for solutes that dissolve into titanium from the mould. The qualitative profiles for contaminants determined by scanning electron probe microanalyser and secondary ion mass spectroscopy in the as-cast titanium were found to be similar to that of microhardness, implying that microhardness can be considered as an index of the contamination resulting from metal-mould reaction.     

Ni|MH二次电池负极用贮氢合金的研究发展

本文详细综述了近年Ni MH二次电池负极用贮氢合金的研究发展概况。依次阐述了AB5、AB2与Ni Ni基、V Ti基固溶体合金以及Mg Ni合金的电化学性能。讨论了改善电化学性能的一些方法 ,同时给出目前一些研究成果     

EMD与KOH溶液的相互影响

利用滴定分析、热失重分析以及XRD方法研究了EMD和KOH溶液混合后的变化。结果表明:碱与MnO2可以相互作用并导致体系温度的升高,碱浓度的下降,EMD中形成Mn3O4以及MnO2中结合水的损失。相互作用的结果与所加KOH溶液的浓度、EMD中的水含量、二者用量的比例关系以及体系的温度有关。     

Magnetism in SiC implanted with high doses of Fe and Mn

High concentrations (0.1–5 at.%) of Mn or Fe were introduced into the near-surface region (≤2000 Å) of 6H-SiC substrates by direct implantation at ～300°C. After annealing at temperatures up to 1000°C, the structural properties were examined by transmission electron microscopy (TEM) and selected-area diffraction pattern (SADP) analysis. The magnetic properties were examined by SQUID magnetometry. While the Mn-implanted samples were paramagnetic over the entire dose range investigated, the Fe-implanted material displayed a ferromagnetic contribution present at <175 K for the highest dose conditions. No secondary phases were detected, at least not to the sensitivity of TEM or SADP.     

注入氮离子的SiC涂层阻氢性能研究

利用离子束混合－离子注入（Ar^ ）和磁控溅射相结合的实验技术在HR－1不锈钢基体上制备了注入N^ 的SiC涂层，并用表面分析手段对所制备涂层的表面形貌，剖面形貌、相结构，表面成分，表面元素的化学态进行了分析，结果表明：制备的涂层结构致密，表面平整、膜层成分均匀；涂层与基体之间形成了一明显的过渡层，增强了涂层和基体之间的结合力，用二次离子质谱（SIMS）对充氘涂层的阻氢性能进行了定性分析，结果表明，涂层元素与氢形成稳定的化学键，抑制了氢的扩散和迁移，使得涂层具有一定的阻氢能力。     

超强吸水树脂的吸水性能研究

对自制的超强吸水树脂的吸收性能进行了研究，分别考察了吸水树脂的粒径，溶液的pH值，几种离子如Na^ ,K^ ,Ca^2 ,Mg^2 等的水溶液对吸水树脂吸收性能的影响。实验结果表明，在pH为6－8，树脂粒径为100mesh-120mesh时，树脂的吸水性能最好，各种离子对吸水树脂吸收性能的影响大小顺序为：Na^ ＜K^ ＜Mg^2 ＜Ca^2 。     

CHARACTERIZATION OF Si_(1-x-y)Ge_xC_y FILMS GROWN BY ION IMPLANTATION AND SUBSEQUENT SOLID PHASE EPITAXY

Si1-x-yGexCy ternary alloy films were grown on monocrystalline silicon substrates by C ion implantation and subsequent solid phase epitaxy (SPE). Two-step anneal-ing technique was employed in the SPE. The structure and electrical properties of the alloy films were determined using Fourier transform infrared spectroscopy and van der Pauw Hall measurements, respectively. With the optimization of two-step anneal-ing technique for the implanted Si1-x-yGexCy layers, a certain amount of C atoms occupied substitutional sites and no SiC was formed.