DS18S20在单总线多点测温系统中的应用技巧

DS18S2 0是一种新型的单总线数字温度传感器。该器件在实际应用中 ,如果使用不当不但无法发挥其优势 ,反而会引入不必要的误差 ,文章重点阐述了它的使用技巧和方法     

The thermodynamic performance of a new solution cycle in double absorption heat transformer using water/lithium bromide as the working fluids

In this paper, a new solution cycle in the double absorption heat transformer is presented and the thermodynamic performance of this new cycle is simulated based on the thermodynamic properties of aqueous solution of lithium bromide. The results show that this new cycle is superior to the cycle being studied by some researchers. This new solution cycle has a wider range of operation in which the system maintains the high value of COP and has larger temperature lifts and operation stability. The relationship between the absorber and the absorbing evaporator is more independent and this makes the operation and control of the system more easier.     

Simulation of the Forming Behaviour of a Boron Modified P91 Ferritic Steel

The forming behaviour at high temperature of a modified 9%Cr‐1%Mo (P91) ferritic steel containing B and Ti for elevated temperature service was investigated. The microstructure of the as‐received material is mainly martensite at room temperature, but special etching revealed prior austenite grains of about 25 μm in size. Torsion tests were conducted at temperatures in the range 850 to 1250 °C to simulate the hot rolling process under comparable conditions of temperature, strain rate and strain. The deformation data obtained from these tests were correlated with the Garofalo equation with a stress exponent of 4.6 and an activation energy of 315 kJ/mol. This equation was used to predict the formability behaviour for the rolling process and also to determine the maximum forming efficiency and stability of the steel. A temperature of 1200 °C is recommended to conduct the forming process.     

控制W9Cr3Mo4V低倍碳化物剥落的工艺改进

针对W9Cr3M04V轧制成品材低倍碳化物剥落的形成原因分析，得出一次碳化物颗粒粗大、在1／4D至中心区域聚集是导致低倍热酸浸试验碳化物剥落的主因；由此进行冶炼过程中注速（锭形）、浇注温度选择对比工艺试验，得出在原有冶炼＋轧制的工艺基础上选用2．2t锭、降低浇注温度（1489℃）能有效改善一次碳化物颗粒大小和聚集程度，进而有效降低低倍碳化物剥落倾向。     

Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

单相负载三相供电功率分配之PLC改造实践

介绍了单相负载一工频感应炉供电的S7-200CPU224改造实践方案.依托原有设备条件,三相功率分配同样设计采用电容、电抗进行调节,起、停及三相电流平衡控制由晶闸管 接触器形式替代原单纯采用接触器控制,有效值测量使用有别于FFT的检测算法.运行实践表明:节能降耗明显,设备故障率大幅降低,具有良好的推广应用价值.     

PbS-Sb2S3-FeS三元系在水蒸气气氛下的铅锑分离

在1073K下通过测定三硫化锑和硫化铅的挥发速度,研究了PbS-Sb_2S_3-FeS三元系在水蒸气气氛下的铅锑分离规律。X-射线衍射结果表明,焙砂由PbS、Fe_3O_4、FePb_4Sb_6S_(14)、Pb_5Sb_4S_(11)和FeSb_2O_4组成。当试样中FeS含量在5％～7％时,铅锑分离效果最好。当试样中FeS的含量≥10％时,铅锑分离效果较差,这时过量的FeS会与Sb_2S_3和PbS形成复杂的硫化物(FePb_4Sb_6S_(14)、Pb_5Sb_4S_(11))或被氧化成F4Sb_2O_4,使锑的挥发变得困难,导致残留在焙砂中的锑含量升高。     

基于S2A6000存储的新闻制播网络安全设计

从分析S2A6000新闻制播网系统特点,拓扑结构入手,完整总结了S2A6000存储的新闻制播网络安全设计与安全措施。