金属注射成形技术进展

分析了影响金属注射成形（ＭＩＭ）产业化进程的两个主要技术因素，即适合ＭＩＭ要求的原料粉末的生产方法和ＭＩＭ生产工艺，并概述了目前ＭＩＭ技术的发展状况。     

磷酸萃取系统中的测量与控制

磷酸萃取是6万t磷铵料浆法流程的关键之一，重要的控制参数有矿浆、硫酸、返回淡磷酸的加入量及萃取槽的液位、压力、温度等。     

OPTIMIZATION OF PRESSURE SWING ADSORPTION EQUIPMENT PART II OPTIMIZATION OF TWO BED OXYGEN GENERATORS

Local equilibrium model described in Part I is used to stimulate both, the steady state operation conditions and transient regime after the start of PSA equipment. The effect of axial dispersion, adsorption isotherm nonlinearity and high pressure level is simulated. On the basis of numerical analysis, the operation of a classical two-bed oxygen generator is compared with two configurations having pressure equalizing step. The optimization strategy of the given PSA equipment has been proposed and the procedure is demonstrated on an example. The scaling-up condition for PSA equipments which can be described by local equilibrium model has been proposed on the basis of the theoretical analysis.     

Cure kinetics and shrinkage model for epoxy-amine systems

Manufacture of most of epoxy resins implies that cure needs to be carried out under pressure. Due to the significance of knowing the influence of the pressure factor in cure kinetics, cure shrinkage of a stoichiometric epoxy-amine system was measured using a pressure-volume-temperature (PVT) analyzer. Recording the specific volume change in the range of temperature from 100 to 180 °C and a pressure of 200 bar we could model the cure kinetics. The Runge-Kutta method was applied to obtain the kinetic constants of the cure reaction. In addition, using the differential scanning calorimeter (DSC) for measurements of 1 bar and the PVT analyzer for pressures of 200, 400, and 600 bar, we also model the kinetic constants as a function of pressure. The results obtained show that the effect of the temperature on the kinetic constants is higher than the effect of pressure. Therefore, both PVT and DSC are complementary techniques to describe the full range of cure kinetic process of epoxy mixtures.     

聚碳酸酯的吹塑成型

简介聚碳酸酯吹塑容器的特性与用途,着重分析其吹塑(包括挤出吹塑、共挤吹塑和注射吹塑)成型的机械(螺杆、机筒、型坯机头与吹塑模具)设计要点及工艺条件。     

容器焊缝错边残余应力与载荷应力的测定研究

本文对焊接容器错边和不错边的焊接接头进行了电测法的残余应力测试，确定了焊接残余应力的大小及方向，并在加载的条件下，对各焊接接头测点进行了综合应力测试，并给出了受载条件下的应力分布。     

新型液晶PVDF合金的研究

本文系统地研究了液晶聚合物(LCP)与PVDF合金共混体系的组成及加工工艺条件对共混物制件性能的影响。并用SEM观察了合金的形态结构。结果表明:在液晶含量10%左右时,加工温度为210℃,合金的拉伸强度最高,磨耗量最低,体系分散均匀并形成了较多的微纤结构。     

A paraffin-fueled SOFC system design and integration

This paper addresses an integrated design of paraffin-reformer, gas separations and the electricity production with a solid oxide fuel cell (SOFC). The overall design consists of three modules. First module is a system of paraffin reformer. In this module, the paraffin feed stream is to send to a steam-reformer. In the second module, the gas separations method illustrated is the combination of a methane-permeable membrane with a pressure-swing adsorption (PSA). In the third module, the purified hydrogen is fed to the SOFC unit. To be energy efficient, this paraffin-fueled SOFC system is designed with the consideration of heat integration. The intent of this paper is to provide a possible, alternative way of cogeneration systems for refinery and petrochemical plants.     

有限长矩形压力容器的应力分析法

对有限长承受内压的矩形压力容器，本文提出了同时考虑矩形容器６个面相互作用的分析计算方法。用所编制的程序计算了一个实际的矩形容器，得到了满意的结果。     

水辅助注塑大直径介质导管制品的冷却分析

采用数学分析方法，通过假设、简化分析模型，用数学模型来表述物理模型，确定了水辅助注塑(VAIM)大直径介质导臂制品的冷却时间，并运用算例和国外试验的结果进行验证。结果发现：水辅助注射成型新工艺可以更加显著地缩短注塑周期，降低制件壁厚，允许制件有更大的实际直径。因此，VAIM技术可用来高效率地生产大直径、高质量、薄壁的介质导臂。