气动增压泵在单片晶圆清洗过程中的应用

主要分析了气动增压泵的组成和工作原理,描述了气动增压泵在单片晶圆清洗过程中的应用特点和优势.介绍了气动增压泵在应用过程中的控制方法和选用注意事项.     

计算机设计软件NX6.0几种复合建模方法

NX软件采用复合（混合）建模技术,本文以“敏于行”为宗旨,运用建模实战领会NX复合建模;本文提出了几种建模方法,分享了NX复合建模的乐趣。     

时间式电控VE泵开发及其控制算法实现

介绍了一种新型的时间式电控VE泵系统。通过对整个喷射系统的电控和机液部分的开发改造,采用了独具特色的控制算法,在原机械泵作最少改动的前提下,实现了喷油量和定时的直接数字控制,该系统已在油泵台试验中得到了验证。     

SEMI-ELLIPTICAL FATIGUE CRACK GROWTH UNDER ROTATING OR REVERSED BENDING COMBINED WITH STEADY TORSION

Abstract— An analysis of the influence of steady torsion loading on fatigue crack growth rates under rotating or reversed bending is presented. Mixed-mode (I + III) tests were carried out on cylindrical specimens in DIN Ck45k steel and results are compared for two different testing machines: rotary bending and reversed bending obtained by cyclic Mode I (Δ K ₁) with or without superimposed static Mode III ( K _III) loading, simulating the real conditions on power rotor shafts where many failures occur. The growth and shape evolution of semi-elliptical surface cracks, starting from a chordal notch on the cylindrical specimen surface, was measured for several Mode III/ Mode I ratios. Results have shown that the steady Mode III loading superimposed on the cyclic mode I leads to a significant reduction in the crack growth rates. It is suggested that this retardation is related to an increase of plastic zone size near the cylindrical surface in association with the interlocking of rough fracture surfaces, friction and fretting debris, leading to a decrease of the ΔK effective at the crack tip profile due to the "crack closure effect". This work provides a contribution to a better understanding of crack growth rates under mixed-mode load conditions thereby allowing one to predict remaining lifetimes and to estimate the risks of pre-cracked rotor shafts.     

糖厂现用连续离心机的研究及生产实践

在各糖厂现用连续离心机原有生产实践基础上，对其机械吸震、加温、布温、机索结构、物料密封、机座等部件做了进一步改进，并取得可观的实效。     

浅谈螺旋密封原理及在电动工具中的应用

介绍了螺旋密封的两种基本结构、工作原理及封液能力的计算和设计方法,得出螺旋密封无泄漏的条件。通过试验,验证了旋向问题的重要性,为螺旋密封的应用提供了经验。     

VILOFT织物的染整工艺

新型VILOFT粘胶纤维织物具有独特的扁平截面，导湿透气，蓬松保暖。本文探讨该纤维织物的前处理，染色，整理工艺，优化并给出了具体工艺参数，对实际生产有一定的参考价值。     

铜精炼阳极转炉氧化期烟气的传热特性

根据能量平衡原理,建立烟气对铜液的传热模型,并对不同空气过剩系数下的烟气平均温度和传热强度进行计算。结果表明:随着空气过剩系数的增大,烟气平均温度和传热强度均有明显下降。为增强烟气对铜液的传热能力,必须适当地减小空气过剩系数。此外,针对燃烧室排烟温度较高的问题,提出采用余热装置回收烟气余热的合理建议。     

利用MBK圆网印花机加工涂层织物的生产实践

介绍了应用ＭＢＫ圆网印花机进行涂层织物生产的经验，包括基布、涂层胶的优选及工艺的制定、工艺参数的确定，并进行了涂层产品的测试。