Second-law-based thermodynamic analysis of two-stage and mechanical-subcooling refrigeration cycles

Thermodynamic analysis of HFC-134a vapor-compression refrigeration cycles is investigated by both the first and second laws of thermodynamics. Second-law analysis is carried out for both two-stage and mechanical-subcooling refrigeration cycles. The analysis is performed on each of the system components to determine their individual contribution to the overall system irreversible losses. It is found that most of the losses are due to a low compressor efficiency. Irreversibilities of expansion valves and condenser are also significant. In addition, it is shown that the optimum inter-stage pressure for two-stage and mechanical-subcooling refrigeration systems is very close to the saturation pressure corresponding to the arithmetic mean of the refrigerant condensation and evaporation temperatures. These results are compared with the existing practice in the industry. Furthermore, theoretical results of a two-stage refrigeration system performance are also compared with experimental values for a CFC-22 system.     

Impact of uncertainties on estimations of heat pump cycle performance

Sensitivity analysis is used to show how uncertainties in basic factors, such as heat transfer, pressure drop, compressor efficiency, and thermophysical properties, influence the result of heat pump cycle performance estimations. By comparing the results of this analysis with uncertainty levels of estimations and experimental determinations, it is established to what extent improvements in accuracy are needed. The investigation was carried out for several different applications and, as working fluids, both pure substances and non-azeotropic mixtures were examined. It was found that evaporation heat transfer and compressor efficiency are two areas where improvements are needed. It is also shown that estimates using very accurate, substance-specific, equations of state differ from those using more general types by up to 1 % for COP and 2% for capacity.     

Ti-6-22-22S合金步进轧制工艺加工棒材研究

采用步进轧制工艺制备了Ti-6-22-22S合金Ф50mm棒材，对加工、热处理、组织与性能的关系进行了分析。结果表明：在两相区上部温度960℃轧制获得细网篮组织，棒材性能较好且数据均匀；热处理后，得到双态组织，强度．塑性达到优良组合，而片层状组织强度较高，但塑性稍低。     

Immobilization of inert TRISO-coated fuel in glass for geological disposal

Vitrification of TRISO-coated gas reactor fuel particles was achieved via two methods: glass melting and sintering. Inert TRISO-coated fuel particles and a borosilicate glass were used. With glass melting at 1200-1300 °C floatation and decomposition of carbon and silicon carbide occurred. Thermal pre-treatment of the particles for oxidation of pyrocarbon did not improve the coating properties of the glass. During cooling most of the particles floated and sorbed on the crucible or mold walls. The sintered glass at 700 °C showed better coating properties of the TRISO-coated fuel particles despite higher porosity compared to glass made by melting. Aqueous leaching properties of glass with particles are similar regardless the mode of fabrication, indicating the good chemical durability of the sintered glass. Sintered glasses may constitute a good technique for TRISO-coated fuel particles immobilization for an eventual deep geological disposal.     

粗甲醇在内燃机上的清洁高效使用

在内燃机排气废热的作用下。液体粗甲醇加压汽化后引入裂解器催化分解为富氢混合气，在上止点附近喷入气缸，发动机采用米勒循环，其功率与效率优于同等结构奥托发动机。     

Kinetic Monte Carlo simulations of radiation induced segregation and precipitation

Kinetics of radiation induced segregation and precipitation in binary alloys are studied by Monte Carlo simulations. The simulations are based on a simple atomic model of diffusion under electron irradiation, which takes into account the creation of point defects, the recombination of close vacancy-interstitial pairs and the point defect annihilation at sinks. They can reproduce the coupling between point defect fluxes towards sinks and atomic fluxes, which controls the segregation tendency. In pure metals and ideal solid solutions, the Monte Carlo results are found to be in very good agreement with classical models based on rate equations. In alloys with an unmixing tendency, we show how the interaction between the point defect distribution, the solute segregation and the precipitation driving force can generate complex microstructural evolutions, which depend on the very details of atomic-scale diffusion properties.     

压水堆核燃料循环的经济分析程序介绍

所开发的压水堆核燃料循环分析计算机经济程序包括12个子程序,代表着压水堆整个核燃料循环各种不同的工艺过程。本程序能算出压水堆核电站核燃料循环中燃料费用对发电成本的影响,给出各工艺过程对燃料成本的敏感度分析,并尽可能给出燃料循环中燃料材料及服务的价格数据.     

步进式加热炉汽化冷却节电初探

介绍了在首钢第一线材厂步进式加热炉汽化冷却设计中，以优化设计改进现有设备和技术，实现了高效节电的效果。     

Supercritical gases pasteurization of apple juice

Supercritical CO₂ and N₂O pasteurization of apple juice, inoculated with Saccharomyces cerevisiae as test microorganism, was performed at 36 °C on a laboratory multi-batch apparatus of a total volume of 150 ml. The pressure values ranged from 100 to 200 bar. Experimental results indicate the effectiveness of the method proposed. A stochastic model of the process was developed on the basis of the experimental evidence: high-pressure inactivation curves were analysed using a stochastic model based on multi-hit model. Furthermore, the samples of the cells subjected to high-pressure treatments were examined by environmental scanning electron microscopy (ESEM) to determine the effect of the process on the cell wall.     

降低氧化铝生产中熟料折合比的探讨

在氧化铝生产过程中，熟料折合比是烧结法一项重要的综合性指标，本文通过对熟料折合比的定义、计算公式的剖析，分析了生产过程中影响熟料折合比的主要因素，对有效降低熟料折合比的措施进行了探讨。