复合材料RTM模具的制备

根据树脂传递模塑(RTM)模具对基体树脂的基本要求,选用双酚A环氧乙烯基酯树脂为基体,聚乙酸乙烯酯为低收缩添加剂,玻璃纤维经编织物为增强材料,并加入相应的助剂,制备了复合材料RTM模具。该模具具有成本较低、开发周期短、精度较高等优点,但表面强度和热效率较低。     

Interaction of Aluminum with Detonation Products

A method of electrical conductivity and an analysis of recovered explosion products are used to study interaction of aluminum with detonation products of condensed high explosives. The electrical conductivity of HMX/Al and RDX/Al mixtures is inhomogeneous; a region with the maximum electrical conductivity is adjacent to the detonation front, whereas the electrical conductivity decreases with distance from the front. If the wave is incident onto a wall, the electrical resistance of the composite high explosive increases, which indicates that the high-conducting zone disappears. The electrical conductivity, resistance of the conducting zone, and the time of resistance growth are found as functions of the particle size of the additive. The results obtained confirm the reaction of the metal additive with detonation products in a microsecond range of time. An analysis of condensed explosion products shows that the reaction of aluminum with detonation products proceeds on the particle surface. The amount of reacted aluminum and the oxide-layer thickness are estimated. __________ Translated from Fizika Goreniya i Vzryva, Vol. 42, No. 1, pp. 120–129, Jnuary–February, 2006.     

Synthetic hydrogels 3. Solvent effects on poly(2-hydroxyethyl methacrylate) networks

Poly(2-hydroxyethyl methacrylate) networks were synthesized in aqueous solutions of propylene glycol, ethylene glycol, ethylene glycol monomethyl ether, or ethylene glycol dimethyl ether and the influences of solvent on phase separation during the polymerization process studied. Results from conversion-phase diagrams, turbidity measurements, swelling studies, and viscosity measurements show that the phase separation process is dependent upon the solubility parameter of the organic solvent, the instantaneous monomer concentration at each stage of the gel formation process, and the crosslinker content of the reaction mixture.     

由氯化钙制备纳米碳酸钙研究

随着国民经济的发展,对纳米碳酸钙的需求量越来越大.基于化工生产中大量副产氯化钙,以氯化钙和碳酸铵为原料,对制备纳米碳酸钙进行了研究.实验研究了添加剂、反应温度和反应物浓度等工艺条件对产物粒径的影响,并采用XRD和TEM对产物进行了初步分析.实验结果表明:不同的添加剂对产物粒径以及形貌具有一定的影响,当氯化钙和碳酸铵配料比为1.0:1.0 mol/mol、反应温度为15℃和氯化钙浓度为0.3 mol/L时,以有机醇A和磷酸系化合物G为添加剂制备的产物为方解石型球状碳酸钙,粒径在50 nm左右.     

EFFECT OF NONSOLVENT ADDITIVES ON THE PORE SIZE AND THE PORE SIZE DISTRIBUTION OF AROMATIC POLYAMIDE RO MEMBRANES

In this paper discussions are made on the effect of nonsolvent swelling agents on the average pore size and pore size distributions at the surface of polyamide membranes which result from casting solutions involving above nonsolvent swelling agents.

The size of the polymer aggregate in the film casting solution and the size of polymer network pores are correlated to physicochemical data of ions which constitute the electrolytes used as nonsolvent swelling agents. As such ionic properties the charge density and the free energy of transition of ions from polyamide phase to water phase were considered. The validity of the correlation is limited in a range of casting solution composition where the polymer concentration in the casting solution is close to the limiting concentration of polymer at the phase boundary and the molar ratio of the nonsolvent swelling agent to the amide group involved in the polyamide polymer is equal to or slightly more than 0.7.     

有机化合物及聚合物的计算机辅助红外光谱法鉴定

建立了计算机辅助红外光谱法鉴定有机化合物及聚合物的新方法,介绍了计算有机化合物和聚合物的一些经验公式。程序设计首先收集、整理常用聚合物、有机添加剂和有机小分子的红外光谱数据,然后提取反映该物质特征的吸收峰数据,制作ACCESS数据库,利用VisualBasicDAO数据链接方式,根据查询要求动态链接数据库,利用要求查询的聚合物特性,经过经验公式的算法翻译,生成SQL查询语句进行查询。     

制浆造纸工业用消泡剂的开发及应用进展

制浆造纸工业生产过程中不可避免会产生泡沫,泡沫控制不当会严重影响制浆造纸工艺条件的执行以及设备的正常运转,导致产品产量和质量降低,而控制泡沫最直接有效的措施是添加合适的消泡剂.该文介绍了制浆造纸工业生产中泡沫的产生和稳定机理,泡沫对制浆造纸工业生产过程和产品质量的影响,并针对制浆造纸生产中制浆、抄纸、涂布和脱墨等工段泡沫特性和消泡要求,综述了制浆造纸用消泡剂的发展历程、各工段消泡剂种类和性质,介绍了消泡剂的研制开发和实际应用成本及使用效果等,并对制浆造纸用消泡剂的发展进行了展望.     

BaTiO3系PTC热敏电阻用施主加入物的研究

阐述了常用的施主加入物、施主加入量、影响施主加入量的主要因素及各施主加入物的特点。研究了常用的施主加入物的理化指标对ＰＴＣ热敏电阻性能的影响，并据此提出了其技术标准。     

Influence of operation parameters on the separation of mixtures by pervaporation and vapor permeation with inorganic membranes. Part 1: Dehydration of solvents

The separation performance of two different commercially available tubular inorganic membranes was studied for solvent dehydration. The separation layers consisted of A-type zeolite and microporous silica. The membrane characteristics were determined as function of operating conditions such as feed composition, temperature, and permeate pressure in pervaporation and vapor permeation. Among different membranes of the same batch, flux and selectivity were reproducible within 10%. The partial flux of water as the preferentially permeating component increases linearly with the water vapor pressure difference between feed and permeate and depends only marginally (viscosity influence) upon the properties of the organic component. The flux of the organic (retained) component is low and can best be described by assuming a substance and membrane specific permeance (flux over partial pressure difference) that is independent of composition. At very low water concentration in the feed one would expect a strong increase in permeability of the retained component through non-zeolite pores and larger silica pores as predicted by pure component measurements. However, this effect was not observed in mixtures within the concentration range studied here. A temperature rise improves flux rates exponentially while selectivity remains high. Thus, higher module cost in comparison to polymeric membranes can be compensated by reduced membrane area if a higher operating temperature can be chosen. Flux and selectivity decline as a function of permeate pressure with decreasing driving force. In vapor permeation with inorganic membranes superheating of the vaporous feed improves their performance while for polymeric materials a steep flux decline is observed. High flux and selectivity are obtained in the separation of water from alcohols. The normalized flux values of the A-type zeolite membrane are roughly 10 kg/m² h bar with a mixture selectivity of 2000 for methanol, 4000 for ethanol and 8000 for n-butanol. The average permeance of the amorphous silica membrane lies above 12 kg/m² h bar with mixture selectivity of 50 for methanol, 500 for ethanol and 2000 for n-butanol. The separation mechanism is mainly based on adsorption and diffusion enhanced by shape selectivity and size exclusion in some cases. The transport characteristics could be described with a simple transport model based on normalized permeate fluxes. With regard to the operation stability of the membranes, no deterioration of the performance was observed for the A-type zeolite in solvent dehydration or in separation of water from reaction mixtures. The silica membrane showed an initial conditioning effect involving a rearrangement of Si-OH groups with an increase in selectivity and decrease in flux of about 30%. After a few hours the performance stabilized and remained constant during further operation.     

钛酸铝材料研究进展及应用

钛酸铝是一种优异的高熔点、低膨胀无机非金属材料。主要阐述了钛酸铝材料的微观结构，以及热分解、热膨胀及其影响因素。简述了钛酸铝材料的制备方法。讨论了合成的工艺条件及添加剂对钛酸铝材料性能的影响，并对其应用作了简单介绍。最后提出了改善钛酸铝材料性能的技术途径。