Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

GaN and AlGaN high-voltage rectifiers grown by metal-organic chemical-vapor deposition

In this paper, we report the study of the electrical characteristics of GaN and AlGaN vertical p-i-n junctions and Schottky rectifiers grown on both sapphire and SiC substrates by metal-organic chemical-vapor deposition. For GaN p-i-n rectifiers grown on SiC with a relatively thin “i” region of 2 μm, a breakdown voltage over 400 V, and forward voltage as low as 4.5 V at 100 A/cm² are exhibited for a 60-μm-diameter device. A GaN Schottky diode with a 2-μm-thick undoped layer exhibits a blocking voltage in excess of ∼230 V at a reverse-leakage current density below 1 mA/cm², and a forward-voltage drop of 3.5 V at a current density of 100 A/cm². It has been found that with the same device structure and process approach, the leakage current of a device grown on a SiC substrate is much lower than a device grown on a sapphire substrate. The use of Mg ion implantation for p-guard rings as planar-edge terminations in mesageometry GaN Schottky rectifiers has also been studied.     

碳纳米管(CNT)场发射显示器的关键技术的研究

对碳纳米管阴极的制备以及场发射显示器的真空封装技术进行了研究.利用一种新的碳纳米管生长工艺制备出了具有优良场发射性能的碳纳米管阴极.并将这种直接生长的碳纳米管薄膜作为阴极,结合一种弹性封装工艺,开发了一种具有简单字符显示功能的场发射显示器.该显示器在较低的工作电压下就可获得高亮度的显示效果,并且器件的亮度与驱动电压成较好的线性关系,这将有利于未来的碳纳米管场发射显示器实现高亮度和多级灰度显示.器件的持续工作寿命测试已经超过5500小时,充分验证了碳纳米管作为场发射阴极的应用潜力.     

Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

ATMOSPHERIC DEPOSITION OF CHEMICAL SPECIES TO POLAR SNOW

Particles and gases can deposit from the atmosphere to polar snow by several mechanisms. Dry deposition can be considered to consist of three steps: aerodynamic transport from the free atmosphere to the viscous sublayer near the surface, boundary layer transport across the sublayer, and interactions with the surface. The particle dry deposition mass flux is dominated by the largest particles present in a size distribution. Wet deposition includes in-cloud and below-cloud scavenging, where the former refers to uptake of particles during nucleation of cloudwater as well as scavenging of particles and gases by existing droplets and ice crystals. Of all the wet deposition mechanisms, nucleation scavenging is often the most important mechanism for particles in the polar regions. Finally, incorporation of particles and gases into fog droplets and subsequent settling of the fog to the snow surface can be an important removal process in regions of frequent fog. For Summit, Greenland, the total deposition of MSA, SO₄^2-, Na⁺, K⁺, and Ca²⁺ during May 24-July 13, 1993 was dominated by wet deposition: this mechanism accounted for an average of 62% of the total deposition for these species. Fog and dry deposition accounted for 21% and 17% of the total, respectively. These results suggest that all three mechanisms may need to be considered when estimating total deposition of certain chemical species to polar snow.     

三峡水库减淤增容调度方式研究——多汛限水位调度方案

本文建议在汛期中小流量时（Q<35000m3/s），将坝前水位维持在148～151m；出现汛情且流量更较大后，将坝前水位降低到143m；入库流量大于35000m3/s且短期预报将出现大于十年一遇洪水时，预泄洪水到135m.按这一调度，汛期约80％时间可以维持在较高水位，一般洪水期。汛限水位143m不影响坝区通航，135m水位迎洪可大量增加防洪库客。到100年后可减淤30亿m3，增加防洪库容约40亿m3.变动回水区减淤40%，优化了坝区水沙搭配，可改善通航条件。降低库区洪水位，缓解防洪与移民的矛盾。可对发电带来较大好处：提高发电效益，减少粗沙过机。初期水库排沙比大于原方案，可减轻下游冲刷。同时，可减小三峡汛初泄水与鄱阳湖防洪的矛盾。     

Skeletal Isomerization and Inter—molecular Hydrogen Transfer Reactions in Catalytic Cracking

Bimolecular hydrogen transfer and skeletal isomerization the important secondary reac-tions among catalytic cracking reactions,which affect product yield distribution and product quality,Catalyst properties and operating parameters have great impact on bimolecular hydrogen transfer and skeletal isomerization reactions .Bimolecular hydrogen transfer activity and skeletal isomrization activity of USY-containing catalysts are higher thn that of ZSM-5-containing catalyst.Coke deposition on the active sites of catalyst may suppress bimolecular hydrogen transfer activity and skeletal isomer-ization activity of catlys in different degrees.Short raction time causes a decrease of hydrogen trans-fer reaction,but and increase of skeletal isomerization reaction compared to cracking reaction in catalytic cracking process.     

Numerical modeling of combustion processes and pollutant formations in direct-injection diesel engines

The Representative Interactive Flamelet (RIF) concept has been applied to numerically simulate the combustion processes and pollutant formation in the direct injection diesel engine. Due to the ability for interactively describing the transient behaviors of local flame structures with CFD solver, the RIF concept has the capabilities to predict the auto-ignition and subsequent flame propagation in the diesel engine combustion chamber as well as to effectively account for the detailed mechanisms of soot formation, NO_X formation including thermal NO path, prompt and nitrous NO_X formation, and reburning process. Special emphasis is given to the turbulent combustion model which properly accounts for vaporization effects on the mixture fraction fluctuations and the pdf model. The results of numerical modeling using the RIF concept are compared with experimental data and with numerical results of the commonly applied procedure which the low-temperature and high-temperature oxidation processes are represented by the Shell ignition model and the eddy dissipation model, respectively. Numerical results indicate that the RIF approach including the vaporization effect on turbulent spray combustion process successfully predicts the ignition delay time and location as well as the pollutant formation.     

碳/碳复合材料CVI工艺中热解碳形成机理的研究

对碳碳复合材料CVI或（CVD）工艺中热碳组织的类型，沉积机理等研究情况进行了简要的综述，并对其进一步研究提出了相应观点。     

化学镀非晶态Ni—B合金的研究

本文通过化学镀方法在铜和钢上沉积非晶态Ni-B合金。着重讨论了还原剂浓度、络合剂浓度对化学镀沉积速率的影响;分析了它的耐蚀原因和其显微硬度随退火温度的变化情况并就其应用和发展略作说明。