悬索桥主缆除湿防腐蚀技术应用和探讨

主缆是悬索桥的“安全生命线”。由于处在跨越江河湖海和承力的环境下,主缆必须进行特殊防护。利用除湿系统干燥主缆内部空气,使湿度保持在一定范围内．可以减缓主缆钢丝的腐蚀。结合传统的主缆缠丝涂装防护方法,分析和讨论除湿系统在主缆防护工程中的应用。     

车载悬架性能检测与可调阻尼减震器

本文采用模糊控制理论，论述了基于被动悬架性能测试基础上的阻尼调节技术，建立了1／4车被动悬架的检测判别理论模型，进行了模拟计算分析，仿真表明，能够提高车辆的安全性，同时，为设计制造性能可靠高效的可调阻尼悬架系统打下良好基础。     

永磁型无轴承电机的完整系统建模

为实现永磁型无轴承电机的稳定悬浮运行，须对转矩和悬浮力进行实时控制。电磁转矩和磁悬浮力的精确计算是无轴承电机设计及其控制的基础。传统的永磁型无轴承电机数学模型将转矩与悬浮力作为两个独立的系统来考虑，忽略了它们之间的非线性电磁耦合关系，因此计算精度不理想。该文通过虚位移法推导、并建立了考虑转矩绕组与悬浮绕组之间非线性电磁耦合关系及转子运动的面贴式永磁型无轴承电机完整系统数学模型，并通过有限元分析提取了模型中的关键参数。基于此模型实现了转子磁场定向控制的悬浮运行仿真，通过与传统数学模型的仿真结果对比，验证了该模型的精确性与完整性。     

基于疲劳理论的汽车空气悬架结构件的弯曲强度计算

针对某种型号客车的空气悬架，应用ANSYS软件对弹簧支架进行了有限元分析，计算了弹簧支架的应力、变形特性，在此基础上计算了弹簧支架的疲劳强度。     

泰州大桥主缆干燥空气除湿法泄漏率的测试实验研究

通过对泰州长江公路大桥主缆送气量和送气压力的数据分析,给出了维护阶段悬索桥主缆漏气量和送气压力之间的半经验公式,对于后期悬索桥在设计使用过程中选择正确的送气压力和送气量有一定的借鉴意义。     

Stability of Extemporaneous Norfloxacin Suspension

The stability of norfloxacin as extemporaneous suspensions compounded from two brands of film-coated tablets (formulas I and II) was studied. The vehicle consisted of tragacanth, saccharin sodium, sorbitol solution, glycerin, paraben concentrate, peppermint spirit BP, purified water, and syrup USP. The final concentration of norfloxacin in the suspensions was 20 mg/ml. Formulas I and II were chemically stable for 28 days when stored in amber glass bottles at ambient temperature; however, their physical characteristics were different.     

Lithography-based ceramic manufacturing (LCM) – Viscosity and cleaning as two quality influencing steps in the process chain of printing green parts

The advantages of suspension based Additive Manufacturing (AM), e.g. the lithography-based ceramic manufacturing (LCM), are high structural resolution, and compared to other available AM techniques, the manufacturing of dense (>99%) ceramic components with high performance. This novel manufacturing technique permits innovative designs, new types of ceramic components, and offers a range of new applications; like micro reactors, catalyst supporting structures or heat exchangers, as well as cutting edge biomedical devices and personalized medical products. Some examples of personalized medical products are customised ceramic knee implants or custom spinal fusion implants. Producing these implants using LCM would allow product offerings not possible before. However, the LCM process chain includes several open points, which have to be solved, in order to get high quality end results. In this paper, the development of suspensions (curable slurries) based on different binders, and the procedures for cleaning printed parts are thoroughly considered.     

Effectiveness of a peracetic acid-based disinfectant against spores of Bacillus cereus under different environmental conditions

A peracetic acid based disinfectant was tested for its efficacy against spores of different Bacillus cereus -strains (DSM 318, 4312, 4313 and 4384). To determine the influence of different factors like exposure-time, temperature and presence of protein quantitative and qualitative suspension tests were performed. Spore suspensions of B. cereus were treated with various concentrations of a representative peracetic acid based disinfectant at three temperatures (10, 15 and 20 °C), with protein load and with different exposure times (5, 30 and 60 min). Temperature, level of concentration and exposure-time had a significant influence on reduction of spores of B. cereus (p < 0.05). The susceptibility of spores of different strains greatly differed. A treatment of spores of DSM 4384 with 2.0% for 30 min even at 10 °C inactivated all present spores (initial number 6.18–6.71 log CFU/ml). Spores of B. cereus strain DSM 4313 had only reductions of 0.16–0.97 log CFU/ml at same treatment conditions. The presence of inactivated bovine serum as interfering substance had no significant influence on reduction (p > 0.05).     

Review of suspension and solution precursor plasma sprayed thermal barrier coatings

As one of the promising methods that can be employed to fabricate high-performance thermal barrier coatings (TBCs), suspension plasma spraying (SPS) or solution precursor plasma spraying (SPPS) has received significant attention in academic research. Enhanced performances have been shown in the SPS-/SPPS-coatings due to their special microstructures, such as uniformly distributed micro-pores, vertical cracks or columnar structures. Since there are more complexities than conventional plasma spraying methods, many works have been devoted to study the mechanism and properties of SPS-/SPPS-coatings during the past decades. In this work, the latest development of SPS or SPPS is reviewed in order to discuss some key issues in terms of preparation of suspension or solution precursor, injection mode of liquid phase, interaction between liquid and plasma jet, microstructure of as-sprayed coatings and corresponding deposition mechanism. Meanwhile, the potential application of SPS or SPPS in some new-type TBCs is introduced at the end of this paper.     

Suspension high velocity oxy-fuel spraying of TiO2: A quantitative approach to phase composition

A range of coatings from a water based suspension of anatase has been prepared by suspension high velocity oxy-fuel spraying with the aim to study effects of heat power of the flame on phase composition, microstructure and surface topography. Three most commonly used approaches of quantitative phase analysis have been scrutinized with respect to their applicability and as some of the coatings showed presence of preferred orientation and it was argued that quantitative Rietveld refinement is the most accurate method for phase composition determination. Coatings had a layered duplex anatase/rutile microstructure with fraction of rutile increasing exponentially with heat power. Spraying at the lower heat power led to a lower surface roughness and higher power resulted in surfaces with pronounced humps, which were distributed homogeneously on the surface. The emergence of humps is related to an increase in macroscopic surface area of up to 30% with respect to the flat coating.