Comparison of Displacement and Mixing Diffusers

In order to cumpare the peformance of different supply diffuers of ventilation air, the airflow passern, temperature stratifiation and contaminant dispersion in a furnitured office ventilated by three kinds of air diffuer were numerically investigated. The air diffuers studied in this paper are a quarter-cylinder displacement diffuer on the floor and mixing diffuers (linear and vortex diffuers) on the ceiling. The heat sources in the of-fice are considered to be 50% convective and 50% radiative. The k-? two-equatwn model of turbulence is employed to predict the turbulent diffusion. The results show that the displacement diffuser provides a rather uniform flow field with low velocify in most areas, and the vertical temperature difference from floor to ceiling is as high as 6 K. With the linear diffuser, the air velociry is high, and the temperature is uniform both horizontally and vertically. The air velocity generated by the vortex diffuser is moderate. The distributions of the temperature and the contaminant are rather uniform.     

Effective lightning protection schemes for distribution line

The causes of lightning outage are subdivided into direct lightning strokes and induced lightning strokes, which are identified by the characteristics of the lightning overvoltage. In the past, lightning protection devices were directed mainly toward the latter, and attention has been focused on the installation of lightning protection devices, ground wires, and reinforcement of insulators. However, lightning outages continue to occur. Thus it is extremely important to clarify the fault characteristics of lightning surges and to study the effectiveness of various lightning protection devices by considering both direct lightning stroke and induced lightning stroke in order to prevent lightning outage in the future. In this research, the electromagnetic transients program (EMTP) has been applied to the direct lightning stroke, and the induced lightning outage analysis program for multiple conductor systems has been applied to the induced lightning stroke to study the effectiveness of lightning protection devices provided by combination of various lightning protection devices. The most effective lightning protection schemes are analyzed and evaluated based on verification tests on the full scale models as well as economic considerations.     

超薄SiO2层的热生长

隧道小孔中超薄ＳｉＯ２的生长是ＥＥＰＲＯＭ电路制造的关键工艺之一。采用ＳＵＰＲＥＭ－Ⅲ工艺模拟程序对超薄ＳｉＯ２的热生长进行了工艺模拟，经过大量的工艺实验及优化，确定了超薄ＳｉＯ２的最佳生长条件，生长出的ＳｉＯ２性能良好，完全可满足ＥＥＰＲＯＭ研制的要求。     

Strain analysis of moving objects using a Fourier transform grid method

There is no good method to measure the shape and the strain distributions of a structure changing with time. We have previously proposed the Fourier transform grid method (FTGM) to measure the three-dimensional shape and surface strain distributions of stationary objects by analysing the two-dimensional grating images recorded with two cameras. In the stereoscopic method, it is very important to determine the accurate geometric parameters of the camera system. In this paper, the positions and the directions of cameras are accurately determined using the FTGM applied to images of a reference object on which a two-dimensional grating is drawn. Applications for analysing shape and strain distributions of vibrating rubber plates and a moving human skin are shown.     

Characterization and modification of fillers for paints and coatings

This paper highlights the possibility of inverse gas chromatography for the surface characterization of common fillers (CaCO₃, talc, SiO₂,) for paints and coatings. Divided solids are described, on the one hand, by the dispersive component of their surface energy and, on the other, by a specific parameter indicating their acid-base interaction potential. The role of the surface morphology at a molecular level is also examined. It is demonstrated that steric effects play an important role in the adsorption of probes on lamellar solids like talc. The consequences of surface treatments as well as examples of practical applications are also reported.     

Bayes estimators for reliability measures in geometric distribution model using masked system life test data

This paper presents Bayes estimators for the reliability measures of the individual components in a multi-component systems in the presence of masked system life test data. The life time distributions of the system components are assumed to be geometric with different parameters. Two-sided Bayesian probability intervals of the parameters are also derived. Numerical simulation study is given in order to: (i) explain how one can apply the theoretical results obtained, (ii) study the influence of the sample size and masking level on the accuracy of point estimates.     

NUMERICAL ANALYSIS AND EXPERI- MENT OF UNSTEADY THERMAL FIELD OF ROTOR PLATE FOR EDDY CURRENT RETARDER

The physical model based on heat transfer theory and virtual boundary method for analyzing unsteady thermal field of rotor plate for eddy current retarder used in automobile is established and boundary conditions are also defined. The finite element governing equation is derived by Galerkin method. The time differential item is discrete based on Galerkin format that is stable at any condition. And a new style of varying time step method is used in iteration process. The thermal field on the rotor plate at the radial and axle directions is analyzed and varying temperature at appointed points on two side-surfaces is measured. The testing and analytical data are uniform approximately. Finite element method can be used for estimating thermal field of the rotor plate at initial design stage of eddy current retarder.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

镨掺杂分布对1.3μm光纤放大器特性影响

对掺氟化镨玻璃光纤放大器的小信号增益，用广义的高斯近似公式可获得精确的分析表达。文中研究了限制光纤芯层中央部分的镨掺杂对光纤放大器特性的影响，结果发现限制镨掺杂分布能改进光纤放大器的工作效率，且截止波长比芯层全部均匀掺镨的光纤更长。