Fringe probing of an evaporating microdroplet on a hot surface

The phenomenon of droplets impacting and evaporating on a hot surface is of interest in many areas of engineering. Quantitative measurement of these processes provides great help to reveal the physics behind. A novel technique was developed to quantitatively measure the volume evolution and contact diameter of an evaporating microdroplet on a hot surface utilizing interference fringe scattering method. In this method, fine fringes produced by the interference of two coherent laser beams was scattered by the droplet and projected onto a screen. The profile and volume of the droplet can be derived from the spatial fringe spacing on the screen. The number of total fringes measurable on the screen was used to determine the instantaneous contact diameter of the microdroplet. Validation experiments demonstrated that the measurement errors are less than ±5% and ±1% for microdroplet volume and contact diameter, respectively. By using this method, the dynamic of droplet impingement, evaporation and boiling using ethanol, pure water and water solution of a surfactant (sodium dodecyl sulfate) with impact velocity of 7.5 m/s and diameters ranged from 0.19 to 0.46 mm were investigated.     

功率电子器件用AlN陶瓷基板的研制

阐述了AlN陶瓷的烧结原理 ,分析了烧结工艺参数对大面积AlN基板性能的影响 ,成功研制出了高热导率(190W /m·K)、大面积 (14 0mm× 90mm)、翘曲度为 2 0 μm/5 0mm的AlN陶瓷基板。     

The Clausius inequality corrected for heat transfer involving radiation

The objective of this paper is to prove that the Clausius inequality must be re-stated to have general applicability for heat transfer involving radiative fluxes. The integrand (đQ/T) of the Clausius expression applies to heat conduction and convection, but does not hold for most radiative transfer scenarios, with the exception of reversible infinitesimal net blackbody radiation transfer. In other cases involving radiative transfer, the equality holds for a cycle even though irreversible heat addition by radiative transfer occurs. This is without the erroneous presumption of entropy destruction anywhere in the cycle. Thus, the Clausius inequality indicates reversibility for a cycle that includes an irreversible process. Further, in some radiative cases the quantity đQ/T, where T is the boundary temperature, is not the entropy transfer at the system boundary, and in fact, primarily represents entropy production within the system. It is also clear that in another case considered, the quantity đQ/T had no physical meaning whatsoever. Consequently, the Clausius expression has been re-stated so that it is applicable to cycles with processes involving any form of heat transfer. A new integrand (đQ_cc/T + đS_Net,Rad) is presented, allowing the Clausius inequality to generally apply to all heat transfer scenarios. The work in this paper emphasizes the need to re-state other fundamental equations allowing applicability to all heat transfer processes, and draws attention to the unique character of radiative entropy calculations.     

Thermal-lens and photo-acoustic methods for the determination of SiC thermal properties

In this paper we report the use of photothermal techniques such as Thermal lens (TL) spectrometry, Photoacoustic and heat capacity, ρc_p, to determine the thermo-optical parameters, such as thermal conductivity (K), thermal diffusivity (D), specific heat (c_p) and the optical path dependence with temperature (ds/dT), of an undoped polycrystalline 3C-SiC. To our knowledge, this is the first time that Thermal lens technique is used for wide band-gap systems. Results obtained for the polycrystalline sample with TL technique indicates that ds/dT is negative at room temperature. Moreover, the obtained values of thermal diffusivity and thermal conductivity are in good agreement with that found in the literature, indicating that the phototermal techniques can be used to obtain the referred parameters in circumstances where other techniques cannot be used, for example, in harsh environments.     

真空制盐蒸发结晶器的设计与实践

真空蒸发制盐外热式强制逆循环轴向出料蒸发结晶器，经多个厂家生产应用实践证明是成功的，具有生命力的。这种新型结构，作为一项新技术新设备应加强研究，总结提高，推广应用。不断完善。文章从流体力学、结晶机理角度要求，到具体工程设计参数和材质选用。论述了该罐的特点。     

Study of hot air generator with quasi-uniform temperature using concentrated solar radiation: Influence of the shape parameters

The non-uniformity of the air temperatures and the slow flow rate at the plane collector exit constitute the main cause of the limitations of the solar drying systems. In order to obtain an uniform and a variable flow rate for different uses, a hot air generator using concentrated solar radiation is proposed. To improve the thermal efficiency of the generator, a study of the influence of different shape parameters is realized. The generator is simulated in the laboratory while investigating the flow induced by a circular disc heated uniformly by Joule effect at constant temperature. This disc is placed at the entrance of an open ended vertical cylinder of a larger diameter. Thermal radiation emitted by the hot disc heats the cylinder wall. The heating of the fluid at the cylinder-inlet generates a thermosiphon flow around the one created by the hot disc. The comparison of the velocity and the temperature profiles of the resulting flow permits to determine the influence of the cylinder height, the vertical source-cylinder spacing and the radius ratio, on the resulting flow at the system exit. Thus, a judicious choice of the shape parameters entails an improvement of the flow rate as well as the thermal flux absorbed by the air and a good homogenization of the air temperature at the generator exit.     

Preparation of CeO2-ZrO2 mixed oxide with high surface area and high thermal stability

Ceria-zirconia solid particles have been recognized as a key material of the automotive exhaust catalysts since they can release and uptake oxygen owing to the rapid reversible oxidation states of cerium between Ce³⁺ and Ce⁴⁺. Several methods have recently been described to prepare the CeO₂-ZrO₂ solid particles used in the catalysts. In this paper, a new coprecipitation method is used to prepare the CeO₂-ZrO₂ solid particles. The Ce-Zr alcogel is dried and calcined in flowing N₂ not in flowing air under atmospheric pressure. The results show that the ceria-zirconia sample calcined at 650 °C has high surface area over 90 m²g⁻¹, which drops to 40 m²g⁻¹ following treatment at 900°C.     

Low temperature synthesis of aluminium titanate by an aqueous sol-gel route

Formation of aluminium titanate (AT) has been achieved at low temperature through sol-gel process using boehmite and titanium hydroxide as precursors by controlling the particle size at nanoscale followed by in-situ peptisation. The formations of AT phase, particle size distributions, sintering and thermal expansion characteristics, and microstructural features have been reported. DTA and XRD analysis have been performed to confirm the formation of AT. A 94% relative density was obtained for aluminium titanate sintered at 1550 °C with controlled grain size in the range of 2-3 μm.     

Gleeble 3800热模拟试验机在宝钢的典型应用与功能开发

热模拟试验可研究成分与各工艺参数对组织和性能的影响，用于指导产品设计和实际生产工艺的制定，还有助于建立数学模型。文章介绍了Gleeble 3800热／力模拟试验机在宝钢实际应用中的几个典型试验，包括高温热塑性试验、多道次变形试验、冷轧薄板相转变点试验和HAZ焊接热影响区热模拟试验等。这些试验可用来解决连铸、轧钢和冷轧产品热处理生产中存在的一些问题。     

Hydrothermal Modeling Studies of Cooling Tower Alternatives

The Environmental Effects Committee of the ASCE Energy Engineering Division has been developing a report on “Energy Production and Reservoir Water Quality” for publication. The report covers the regulatory framework that dictates much of the procedures for studies related to this topic, the fundamental reservoir hydrodynamics and water quality modeling used in preparing studies, the kinds of studies that can be prepared at different levels of analysis, and a series of applications that illustrate the problems encountered and applications of the various techniques. This study of hydrothermal modeling as applied to examining cooling tower alternatives for an existing steam electric station on a moderately large reservoir is included in this report and is presented here as an illustration of the types of studies included. This particular study subtended the usual steam electric plant cooling water discharge studies that relate to specific regulatory thermal plume size standards, and had to be designed around developing plant and cooling tower operations that would meet specific fisheries requirements for a zone of passage and refuge for fishes throughout the receiving embayment. After being used in developing cooling tower and plant operating details for the designers to work with, it was required that the hydrothermal modeling results be verified under actual tower operating conditions. In addition, it was required that the impact of the combined operations on dissolved oxygen be examined in detail. This paper covers the background to setting up the study, the kinds of statistical comparisons used to verify the hydrothermal studies, and similar studies for the analysis of dissolved oxygen distributions.