Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

Mechanical and thermal properties of HVOF sprayed Ni based alloys with carbide

The objective of the present study is to develop multi-functioned coating to the components, which are made of copper with electroplated Ni and are widely used for steel making industry. In this paper, we report the mechanical and thermal properties of Ni based superalloys with carbide sprayed by high velocity oxygen fuel (HVOF), and the detailed effects of sprayed material, spraying conditions, and initial powder structure on these properties. It was found that, among commercial Ni self-fluxing alloys (without fusing treatment), coating with a carbon content of 0.58 mass% had the most preferable properties, with a good balance of the hardness, strength, and thermal shock resistance. The thermal shock resistance depended not only on the strength of the coating but also on the volume contraction when tested at high temperatures. For the several developed Ni based superalloys with carbide, Ni20Cr8Mo5Fe–WC and Ni16Cr15Mo3–WC demonstrated the prominent adhesion strength and thermal shock resistance with high Galvanic corrosion resistance through optimized spraying condition. Also, 20 mass% NiCr–Cr₃C₂ coating sprayed by using employed relatively small primary particle succeeded in achieving the multi-superior properties; high adhesion strength, high corrosion resistance and thermal shock resistance.     

住宅隔热的影响因素及设计对策

夏季 ,室外气候诸因素经过不同途径 ,对室内的影响会有差异。了解这些差异有助于在设计时把握主要问题。讨论在住宅隔热设计中 ,针对不同的室内条件 ,应优先考虑的因素及相应的设计对策。     

Nonlinear coupled problems in dynamics of shells

The coupled system of three partial differential equations governing a flexible shallow shell dynamics is analysed. No any prior assumptions about the temperature distribution through the shell thickness are applied. The efficiency of the method used here when applied to the solution of integral-differential equations with different dimensions (three-dimensional equations related to the Kirchhoff-Love model) and of different type (heat transfer equations and the hyperbolic equations of shell theory) is demonstrated. Many computational results are reported and discussed.     

阀控式铅酸蓄电池的维护

对阀控式铅酸式蓄电池的维护工作进行了初步探讨。     

Fabrication of sharp silicon tips employing anisotropic wet etching and reactive ion etching

We developed a process to obtain sharper silicon tips by employing anisotropic etching in a KOH solution followed by SF₆ plasma etch. The tips were further sharpened using the established thermal oxidation technique to decrease the cone angle and, therefore, obtain smaller curvature radii. We have analyzed the impact of such changes in geometry on a figure of merit associated with the field emission characteristics. An increase in the figure of merit by a factor of three was found in relation to the tips before sharpening.     

关于离子注入中温升的探讨

本文在理论和试验两个方面探讨了离子注入中的热效应和温升现象。注入样品的温升对离子注入层的性能有直接影响。分析了理论计算注入样品温升的一些情况。给出了实际测量注入样品温升的几种试验方法。阐明了控制注入样品温升的若干可能途径。     

Evidence of thermally induced borehole elongation: a case study at Soultz, France

When they occur, borehole breakouts are considered strong markers of principal stress directions at depth. An innovative processing method for automatically identifying breakouts from ultrasonic borehole wall images has been developed. It has been applied to data sets from two deep, sub-vertical wells (GPK1 and GPK2) at the Soultz geothermal site in eastern France. In well GPK1, below 3 km depth, compression breakouts, with a 95°±7° azimuth, increasingly occur with depth. They result from time dependent compression failure at sub-critical stress levels and are indicators of the minimum horizontal principal stress orientation. However, in the uppermost logged section of well GPK2 (1.6–2.9 km depth), continuous borehole elongations share roughly the same azimuth with so called drilling-induced fractures (164°±18° and 175°±17° azimuth, respectively). Both features concomitantly vanish with depth, together with the amplitude of the thermal perturbation induced by drilling. It is proposed that these latter borehole elongations result from a pervasive, cooling-induced, tensile micro-cracking process prior to macroscopic failure localization. They are termed thermal elongations and are indicators of the maximum horizontal principal stress orientation. Had a simple logging caliper tool been used for this work, these thermal elongations might have been confused with classical compression breakouts. A simple criterion for differentiating compression breakouts from thermal elongation is proposed.     

煤矸石作水泥混合材的活化方法研究

论述了煤矸石用作水泥混合材时如何激发其活性的若干方法 ,介绍了通常所用的热激活、物理激活和化学激活煤矸石的机理。实验显示了各种激活方法的效果 ,近而讨论了提高煤矸石活性时应注意的问题