液体低温热导率的测试

介绍了非稳态法测试液体在低温下（－１００～５０℃）的热导率的测试原理、方法，测试了全氟三乙胺的低温热导率。为了提高测试的重复性，采用了相对比较法，并给出了测试装置及测试结果和误差分析。     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

Thermal Characterization of 1.3 μm InAsP/InGaAsP Ridge Waveguide MQW Lasers Based on Spectroscopy Method

An experimental way to analyze the thermal characterization of semiconductor lasers based on spectroscopy method under pulse driving conditions has been developed. By using this way the thermal characteristics of strain compensated 1.3 μm InAsP/InGaAsP ridge waveguide MQW laser diodes have been investigated. Results show that by measuring and analyzing the lasing spectra under appropriate driving parameters and temperature ranges, the thermal resistance of the laser diodes could be deduced easily. A higher thermal resistance of 640 K/W has been measured on a narrow ridge laser chip without soldering. Other thermal and spectral properties of the lasers have also been measured and discussed.     

红外热成象技术在股骨头坏死疾病针刺疗法中的应用

红外热成象技术可以有效地用于股骨头坏死疾病的诊断和针刺治疗效果的评价，效果优于其它常规方法。     

宜昌地区下寒武统沉积环境分析

宜昌地区早寒武世除天柱山期(南部和西部称岩家河期)岩性变化较大外,其他依次沉积了以黑色炭质页岩夹灰岩、细碎屑岩、石灰岩、白云岩等为主的岩性组合,反映了中扬子区岩性四分的特点。晚震旦世灯影末期区内是一个东高西低、东北高西南低的浅海沉积区。在此背景上,早寒武世早期(即天柱山期)遭受了短暂而快速海进之后,依次经历了浅海盆地边缘、斜坡带、浅海陆棚及潮坪等沉积环境的缓慢演化,显示了有规律的海退序列。在区内天柱山组、岩家河组及水井沱组等均首次发现了重力流沉积;在水井沱组下部炭质页岩所夹的薄层粉晶云岩中,首次发现了沉积型重晶石富集层。根据区内天柱山期为浅海斜坡带(岩家河期为浅海盆地边缘)、水井沱期为浅海盆地边缘至斜坡带等沉积环境判断。天柱山组(岩家河组)与水井沱组之问应为连续沉积、整合接触。图3表1参7     

半绝缘砷化镓中碳含量对热稳定性的影响

本文报导了LEC法半绝缘砷化镓单晶中含碳量对SI-GaAs热稳定性的影响。在800℃以上退火,发现当晶体中C含量大于1.5×10~(16)cm~(-3)时,SI-GaAs的热稳定性变差;而C含量小于5×10~(15)cm~(-3)时,通常表现出良好的热稳定性。     

本征吸除硅片特性研究

本文描述硅本征吸杂片的特性参数,如吸除区宽度、洁净度,氧沉淀密度、MOS电容寿命,介绍了表面态密度及残余间隙氧浓度的检测方法和工艺对参数的影响及参数之间的内在联系,文章还实验论证了不同参数水平对器件成品率的影响,建立了以MOS电容寿命为主导的参数控制方法,利用本文提供的控制参数,可使CCD-512器件成品率达60％,以上优品率≥85％。     

Microstructural Effects of Ion Implantation on Molybdenum

The effects of ion implantation and subsequent annealing on the microstructure of molybdenum have been investigated by transmission electron microscopy. The ions investigated were carbon, nitrogen, and tellurium. The ion-induced damage was found to give rise to grain boundary migration phenomena both during implantation and during subsequent annealing. Precipitation or ordering was found to occur for each ion on annealing.     

石英晶体监控法镀制高精度光学薄膜

讨论了石英晶体监控法在光学薄膜镀制过程中的应用原理。通过与常规的光学监控法镀制的膜层相比较．证实了石英晶体监控法有助于提高光学薄膜的光学品质。试验表明所镀膜层的光学性能优异，在光通信和激光器等领域具有广阔的应用前景。     

同步辐射晶体单色器晶体热应变的模拟与实验结果的比较

报道了同步辐射装置光束线关键部件之一的晶体单色器晶体热应变的ANSYS有限元模拟结果,并与实验结果进行了比对,模拟结果在实验误差范围(约士15%)内与实验数据符合,证明了模拟结果的可靠性.