A Model for Through Drying of Tissue Paper at Constant Pressure Drop and High Drying Intensity

A mathematical model for through drying of paper at constant pressure drop was developed. The model is based on physical properties; hence, basis weight, pressure drop, drying air temperature, pore size distribution, initial gas fraction, and tortuosity are important input parameters to the model. The model was solved for different combinations of the variables basis weight, drying air temperature, and pressure drop corresponding to industrial conditions and the results were compared with data from bench-scale experiments. The simulations show that the drying rate curve is very sensitive to the air flow rate and that correctly modeling the correlation between pressure drop and air flow rate is the most important factor for a successful model for through drying. The model was tuned by adjusting the parameters initial gas fraction and tortuosity in order to give the best possible fit to experimental data. For a given basis weight and pressure drop, different drying air temperatures resulted in relatively constant values of the fitted parameters. This means that the model can well predict the effects of changes in drying air temperature based on a tuning of the model performed at the same basis weight and pressure drop. However, for a given basis weight, an increase in pressure drop yielded fitted parameters that were somewhat different; i.e., a lower initial gas fraction and a higher tortuosity, a change that increases the resistance to air flow. This implies that the correlation between pressure drop and air flow rate in the model does not quite capture the nonlinear relationship shown by the experiments.     

气囊在建筑施工中的应用

对气囊在路基压实密度检测、空心板梁制作和大型混凝土构件搬运中的运用进行了分析,指出将气囊这种先进的施工工艺应用到建筑施工中,加快了施工进度,确保了工程施工质量,并降低了工程施工成本,值得推广使用。     

Analysis of supersaturation and nucleation in a moving solution droplet with flowing supercritical carbon dioxide

A supercritical antisolvent (SAS) process is employed for production of solid nanoparticles from atomized droplets of dilute solution in a flowing supercritical carbon dioxide (SC CO₂) stream by attaining extremely high, very rapid, and uniform supersaturation. This is facilitated by a two‐way mass transfer of CO₂ and solvent, to and from the droplet respectively, rendering rapid reduction in equilibrium solubility of the solid solute in the ternary solution. The present work analyses the degree of supersaturation and nucleation kinetics in a single droplet of cholesterol solution in acetone during its flight in a flowing SC CO₂ stream. Both temperature and composition are assumed to be uniform within the droplet, and their variations with time are calculated by balancing the heat and mass transfer fluxes to and from the droplet. The equilibrium solubility of cholesterol with CO₂ dissolution has been predicted as being directly proportional to the Partial Molar Volume Fraction (PMVF) of acetone in the binary (CO₂–acetone) system. The degree of supersaturation has been simulated up to the time required to attain almost zero cholesterol solubility in the droplet for evaluating the rate of nucleation and the size of the stable critical nuclei formed. The effects of process parameters have been analysed in the pressure range of 7.1–35.0 MPa, temperature range of 313–333 K, SC CO₂ flow rate of 0.1136–1.136 mol s^?1, the ratio of the volumetric flow rates of CO₂‐to‐solution in the range of 100–1000, and the initial mole fraction of cholesterol in acetone solution in the range of 0.0025–0.010. The results confirm an extremely high and rapid increase in degree of supersaturation, very high nucleation rates and stable critical nucleus diameter of the order of a nanometre. Copyright © 2005 Society of Chemical Industry     

非标准工况下空分设备增产氩的研究与实践

文章对非标准工况下的空分设备增产氩措施进行了研究。以宝钢6#60000m3/h空分设备为例,通过设计型算法和校核型算法,建立了空分设备精馏的数学模型,通过改变数学模型的参数,分析了在非标准工况下精馏塔内的组分浓度分布,并提出了优化后的操作方案和操作参数,实施后提高了空分设备的氩提取率,取得了显著的经济效益。     

夏热冬暖地区住宅平面设计与空调能耗关系分析

夏季住宅空调能耗已成为目前广州地区电力过荷的一个主要原因，而目前建筑师对住宅设计中的空调能耗因素并未有深入的考虑。本文就广州地区中高层住宅标准层平面设计中的朝向、形状、大小及层高与空调能耗关系进行了相关的分析，适用于夏热冬暖地区。     

In the theory of blast waves

The behavior of the blast wave from an exploding spherical volume is investigated mathematically over the entire range of blast-wave propagation. The computational method uses analytical results for a similar problem for a point explosion with counter pressure and the theory of an asymptotically equivalent point explosion. The asymptotic solution of the gas-dynamic equations away from the explosion site is matched to the initial conditions of blast-wave formation due to the disintegration of the detonation shock upon its arrival at the boundary of the exploding volume. The spatial distribution of the blast-front pressure is found for combustible gaseous systems and solid explosives. The theoretical results obtained agree quantitatively with available experimental measurements. __________ Translated from Fizika Goreniya i Vzryva, Vol. 42, No. 4, pp. 93–99, July–August, 2006.     

A scheme to randomly generate surface dust points for the 3D complex variable boundary element method (CVBEM)

A scheme to randomly generate dust points on the surface of a three-dimensional (3D) object is proposed. This scheme will potentially eliminate the bias of a density of points which are approximately equally spaced on the surface, as well as eliminate possible weighting requirements for areas of higher density. This method has the potential to reduce computational effort, as fewer points might be required to define the surface area. The global trial function vector can be assigned to these dust points and then entered into the complex variable boundary element method (CVBEM) commercial code. This scheme can be applied to each piece of a system that is comprised of a connected multiple geometry. A noticeable benefit of this approach is that the same problem can be studied several times, using a new random distribution of surface points each time. The smallest error can then be determined and that run selected. The Mathematica code used to generate the scheme is attached as an appendix.     

变温条件下HDPE/CB的正电子湮灭特性

对掺杂了25份（phr）导电炭黑（CB）的样品进行了正电子湮灭寿命谱的变温测量，在玻璃化转变温度以上，随着温度的增加，自由体积的大小线性增加，在玻璃化转变温度以下，自由体积的大小基本不变，o-Ps的强度在－40℃下基本不变，从－40℃以上开始增加，但在50℃以上上升有加快的趋势，与PTC材料的PTC现象和导电性能有一定的关联。     

汽车空调冷凝器腐蚀试验的表征与评价

介绍了汽车空调冷凝器的腐蚀试验程度及方法，对试验后的冷凝器进行了密封性检查，并用光学显微镜和扫描电镜检测和分析了材料的显微结构，焊接质量，腐蚀性质及其腐蚀深度等。通过对冷凝器的宏微观检查与表征，评价了冷凝器质量的优劣，提出了改进措施与建议。     

浅谈诺兰达工艺控制

介绍了诺兰达炉氧平衡控制方法 ,对控制中常见的问题总结了一些相应措施。