硅表面上的纳米量子点的自组织生长

纳米半导体量子点以其所具有的新颖光电性质与输运特性正在受到人们普遍重视。作为制备高质量纳米量子点的工艺技术 ,自组织生长方法倍受材料物理学家的青睐。而如何制备尺寸大小与密度分布可控的纳米量子点更为人们所注目。因为这是关系到纳米量子点最终能否器件实用化的关键。文中以此为主线 ,着重介绍了各种 Si表面 ,如常规表面、氧化表面、台阶表面以及吸附表面上 ,不同纳米量子点的自组织生长及其形成机理 ,并展望了其未来发展前景     

化学束外延

本文介绍了化学束外延(CBE)的发明和发展,论述了CBE的原理和设备。文中还介绍了最近提出的一种生长机理。     

过共晶Al－Si合金共生区激光表面处理

用２ｋＷ连续ＣＯ２激光对过共晶Ａｌ－１８Ｓｉ合金以不同能量密度和扫描速度进行快速熔凝处理。用扫描电镜、电子微区分析仪分析了微观结构。从计算机对Ａｌ－Ｓｉ合金ｆ－ｎｆ系统的非平衡理论计算所得的共生区及实验结果的分析可见，当能量密度和扫描速度决定的凝固条件处于共生区中部时，过共晶Ａｌ－Ｓｉ合金激光表面处理可以得到共晶间距低于２００ｎｍ的完全共晶结构。     

In－BiCaVIG的晶体生长与性能

本文报导了用助熔剂法成功地生长大尺寸掺铟ＢｉＣａＶＩＧ晶体的方法以及实验结果，介绍了该单晶在近红外区的磁光器件中的重要应用。     

纤维共晶生长界面前沿三维扩散场解析

修正Ｊａｃｋｓｏｎ和Ｈｕｎｔ关于在垂直生长方向截面上溶质扩散各向同性假设，求解三维Ｌａｐｏｌａｃｅ方程，获得纤维共晶生长界面前沿三维稳态扩散场，并证明Ｊａｃｋｓｏｎ和Ｈｕｎｔ的二维模型是实际生长的二维简化和一阶近似，并用丁二腈（ＳＣＮ）一梓脑（ＣＡＭ）纤维共晶系统计算生长界面前沿溶质分布。     

Studies of photoconductivity in β-Apo-8′ carotenal

The photoconductive properties of a carotenoid polyene,β-Apo-8′ carotenal in polycrystalline form has been studied. The growth of the photocurrent shows an overshoot in the growth-time curve before steady state value is attained. This behaviour of photocurrent is proposed to be due to higher value of recombination coefficient than trapping coefficient. From the temperature dependence study it is observed that the steady state photocurrent, at first increases with increase of temperature, attains a maximum at a particular temperatureT _max and then decreases with temperature. TheT _max value agrees with the temperature above and below which steady state photocurrent is attained differently. Monomolecular and bimolecular recombination processes at two temperature regimes are proposed to account for the observed behaviour. The dependence of photocurrent with excitation light intensity and wavelength study provide information on the carrier generation processes. The fast decay of photocurrent have been observed at different temperatures and from this study the decay constant is calculated and it is found to be temperature independent.     

A computational model for analysing interactive buckling and delamination growth in composite structures

In this paper, a unified method is presented: (i) to model delaminated stiffened laminated composite shells; (ii) for synthesising accurate multiple post-buckling solution paths under compressive loading; and (iii) for predicting delamination growth. A multi-domain modelling technique is used for modelling the delaminated stiffened shell structures. Error-free geometrically nonlinear element formulations — a 2-noded curved stiffener element (BEAM2) and a 3-noded shell element (SHELL3) — are used for the finite element analysis. An accurate and simple automated solution strategy based on Newton type iterations is used for predicting the general geometrically nonlinear and postbuckling behaviour of structures. A simple method derived from the 3-dimensionalJ-integral is used for computing the pointwise energy release rate at the delamination front in the plate/shell models. Finally, the influence of post-buckling structural behaviour and the delamination growth on each other has been demonstrated.     

Morphological and kinetics study of PEO/PVC blends

The kinetics of spherulite radial growth and the morphology of the compatible system PEO/PVC have been studied by optical microscopy. The usual spherulite radial growth behaviour has been found for compatible blends with PEO content higher than 70%. For lower composition, distortion of the usual spherulite morphology has been observed; the anomalies have been attributed to partial miscibility of the components.     

Selective area epitaxy of CdTe

We have performed selective area epitaxy (SAE) of CdTe layers grown by molecular beam epitaxy using a shadow mask technique. This technique was chosen over other SAE techniques due to its simplicity and its compatibility with multiple SAE patterning steps. Features as small as 50 microns × 50 microns were obtained with sharp, abrupt side walls and flat mesa tops. Separations between mesas as small as 20 microns were also obtained. Shadowing effects due to the finite thickness of the mask were reduced by placing the CdTe source in a near normal incidence position. Intimate contact between the mask and the substrate was essential in order to achieve good pattern definition.     

INHIBITION OF BEER-SPOILAGE LACTIC ACID BACTERIA BY NISIN

149 strains of bacteria, mostly brewery contaminants able to spoil wort or beer, and 12 brewing strains of yeast (8 ale and 4 lager strains) have been screened using a well-test assay for sensitivity to the food preservative, Nisin (E234), Nisin inhibited growth of 92% of the gram-positive strains, predominantly lactic acid bacteria of the genera Lactobacillus and Pediococcus. In contrast, all 32 gram-negative strains tested, except 3 Flavobacter strains, were Nisin-resistant; in addition none of the brewing yeasts showed Nisin-sensitivity. Therefore. Nisin has potential applications in preventing spoilage of worts or beers by lactic acid bacteria.