PX氧化鼓泡塔反应器内的TA浓度分布

利用新建的D476鼓泡塔冷模实验装置和沉降—扩散模型对工业鼓泡塔PX氧化反应器内的TA浓度分布进行了实验和数学模拟研究。结果表明,由于PX氧化气速较大,塔内TA浓度接近均匀分布。     

垂直管内弹状气泡上升中壁面传递的实验研究

垂直管内弹状流壁面传递是诸多工业应用中需研究的重要问题之一。今用极限扩散电流技术,对弹状气泡上升时瞬时壁面剪应力和传质系数进行了测定,结果显示:当基于表观气速的Froude数FrG < 0.74时,壁面剪应力随弹状气泡和液塞的到来呈现方向相反的交替变化,壁面传质系数亦相应变化;而当FrG > 0.74时,剪应力方向一直向下,说明液膜向下流动,且弹状气泡和液塞的到来对壁面传质系数的影响很小。这说明下落液膜射流穿透了液塞段,控制了整个壁面传递过程。研究还对下落液膜区、尾迹区及液塞段的不同传递特征及机理进行了分析, 并结合气泡塔熔融结晶器中弹状气泡上升时的传热,对结晶操作条件的合理选择进行了讨论。     

XK908耐高温蒸煮胶粘剂的研制与应用

叙述了ＸＫ９０８耐高温蒸煮胶粘剂的制备方法，主要反应条件对缩聚反应和扩链反应的影响，并对产品的应用效果与国外同类产品进行了比较     

Bubble Formation at a Rotating Cylindrical Surface in Cross‐Flowing Liquid

A novel method of gas sparging from a rotating cylinder is proposed, which prevents against formation of large attached gas cavities in cross‐flowing liquids including those flowing downwards. Experimental and theoretical results regarding critical rotation speed necessary to remove the attached cavity, bubble formation process and size distribution of the produced bubbles in a low viscosity system (air‐water) are presented in this study.     

油滴釉制作工艺的研究

在研制氧化气氛烧制油滴黑釉器的基础上 ,探讨了影响油滴釉形成的工艺因素。通过一系列试验 ,进一步验证了油滴釉在结晶过程中主要发生了液液分相 ;釉料的化学组成是油滴晶斑形成的先决条件 ;釉层厚度、烧成制度等是决定釉面效果的重要因素 ;油滴晶斑的呈色不仅与烧成气氛有关 ,还与着色氧化物的引入有关。     

熔块中的气泡缺陷及其解决办法

分析了熔块生产中气泡缺陷产生的各种原因．提出了实际生产中的注意事项和具体的解决办法。     

MathCAD软件对塑料发泡振动的模拟

气泡膨胀过程中产生的高频振动已达到超声波范围,对聚合物中纳米粒子的分散具有很好的作用。利用MathCAD模拟了气泡振动影响因素,分析了气泡内外压差、高聚物熔体的表面张力、应力松弛时间等因素对气泡振动的影响。通过分析,对气泡振动的工艺条件提出一些参考。     

煤液化油实沸点蒸馏的模拟实验

采用TD200简易蒸馏装置对石油醚和液体石蜡进行了实沸点蒸馏，得到实沸点蒸馏数据，并绘制了实沸点蒸馏曲线和各馏分质量百分数与温度关系曲线，得出主要馏分所在的沸程分别为石油醚64．5℃～68℃，液体石蜡412℃～420℃；同时计算出了二者的平均沸点为65.73℃和404．36℃．这些曲线及数据不仅对石油醚和液体石蜡的组成和使用性能有参考价值，而且这种分析方法为煤液化油的实沸点蒸馏奠定了基础。     

Chaos in bubbling—nonlinear analysis and modelling

In the present paper, nonlinear features and analytical results for the chaotic bubbling from a submerged orifice are described. A chain of air bubbles was produced from the single orifice of in diameter and micro-convection induced by the bubble generation was recorded using hot-probe anemometer located close to the orifice. The air flow rate was varied widely from q=100 to and the aspects of bubbling were observed by high-speed video. The nonlinear analysis is performed for the time series data of hot-probe anemometer especially in the range of q=435-. The calculated largest Lyapunov exponent shows that with increase of air volume flow rate, the time period for the process of liquid flow to lose stability becomes shorter and at high air flow rate such as , it is shorter than the time period between subsequent bubbles. To explain such chaotic behaviors of bubbling, a simple model has been proposed. The model simulates the process of interaction between the elastic bubble wall and liquid. Simulation results compared well with the analytical results of experimental data. Summarizing, it is concluded that one of the reasons for chaos appearance is the nonlinear character of interaction between an elastic bubble wall and the liquid stream.     

Observation of 3‐D Structure of Bubbles in a Fluidized Catalyst Bed

The interface area between the bubble and emulsion phases in a fluidized catalyst bed is one of the important parameters used to analyze and design the fluidized bed reactor. We used a fast‐scanning X‐ray CT system to observe the bubble shape and structure. We then obtained the transient 2‐dimensional cross sectional gas‐phase distribution in a fluidized catalyst bed. Using image‐processing techniques, pseudo 3‐dimensional images of the bubbles were reconstructed. The bubble structure was studied based on the 3‐dimensional images and the previously obtained results in a 2‐dimensional fluidized bed. It was found that the bubble shape was not spherical but complicated, and that the bubbles ascending in a fluidized catalyst bed consisted of some smaller bubbles.