ADSS光缆的力学计算

介绍了ADSS光缆的力学计算，给出了光缆弧垂、张力、应变和悬长等计算公式，并对普遍采用的“悬链线”和“抛物线”两种计算方法加以比较。     

我国有线电视的网络媒体价值

阐述有线电视网络媒体的特点，有线电视网络媒体面临的困境及解决办法，最后展望有线电视网络媒体价值。     

ATH在无卤阻燃聚乙烯电缆料中的应用研究

以EVA改性LDPE,以偶联剂改性ATH,通过一系列配方的研究和性能测定,认为可以设计出适合于电缆料用的无卤阻燃聚乙烯的配方。     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

A time series approach to fatigue crack propagation

The inherently nonlinear phenomenon of fatigue crack propagation is modeled as a linear random process. To a first approximation, simple, nonstationary time series models are introduced and standard techniques for determining the parameters of autoregressive integrated moving-average processes are applied. Multiplicative time series models are next utilised for the representation of a group of crack history curves. Implementation of the models on the Virkler experimental data set yields satisfactory results. Reliable Gaussian approximations to the distribution of the time required by a crack to reach a specified critical length are obtained, and the usefulness of the approach is demonstrated when updating lifetime predictions after periodic inspections.     

环境因子的定义及研究现状

从普遍接受的三个基本假设出发，讨论环境因子的定义和失效机理不变的约束条件，重点综述环境因子的研究现状和常用方法，并探讨引入反应论模型解决环境因子预测问题的可能途径。     

列车客车用低温发热电缆地面辐射供暖系统的实验研究

对不同地板结构和不同导线间距下发热电缆地面辐射供暖系统的热工性能进行了测试分析，考察了系统的稳定性和可靠性，给出了综合比较结果，分析了影响发热电缆地面辐射供暖系统热工性能的主要因素及其影响规律。     

Fatigue crack growth analysis of welded aluminium RHS T-joints with manipulated residual stress level

The fatigue life of a welded aluminium T‐joint made from beams with rectangular hollow section (RHS) has been predicted using a crack propagation analysis and compared with experimental results from joints with different residual stress levels. To include the effect of the residual stresses, the stress ratio was calculated at the weld toe and, via Walker's equation, introduced into the analysis. How to obtain the Walker exponent has been discussed in detail. The introduction of a stress ratio at the weld toe provides good agreement between the experimentally and analytically found S–N curves. The effect of the residual stress was successfully included in the analysis.     

连铸转炉钢包电力牵引车的研制

论述研制连铸转炉钢包牵引车的目的、意义、方案的选择及设计计算校核,对技术要点作出了明确阐述.     

Estimating thermal stress in BIPV modules

The thermal stress on building‐integrated photovoltaic modules (BIPV) in Espoo, Finland, was studied with field‐testing of amorphous silicon modules. Based on these results, the thermal stress at two other European locations (Paris and Lisbon) was estimated. The estimation procedure entailed thermal modelling of heat transfer in the façade with meteorological data as input. The results indicate that the thermal stress on BIPV modules in Lisbon is, in this case, approximately 50% higher that in Espoo and between 80 and 200% higher than in Paris, depending on the activation energy of the degradation process. The difference in stress between a BIPV module and a free‐standing module in Espoo was 50–200%. Copyright © 2006 John Wiley & Sons, Ltd.