Development of a predictive model for polymer/solvent diffusion coefficient calculations

A new calculation procedure for free‐volume parameters is considered in this work by using viscosity prediction methods and the Levenberg‐Marquardt calculation scheme. All parameters used in the Vrentas–Duda free‐volume theory can be estimated from pure component properties. The prediction results are compared with experimental data for some polymer/solvent systems. The diffusion coefficient calculated by Vrentas–Duda theory can be used in the modeling of membrane separation processes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Towards a new definition of EPOC parameters for anionic electrochemical catalysts: case of propene combustion

The electrochemical promotion of catalysis (EPOC) of propene combustion was investigated using Pt sputtered thin film on an O²⁻ conductor, 8 mol% Y₂O₃-stabilized-ZrO₂ (YSZ). In order to separate the influence of the thermal migration of the O²⁻ oxide ions from the electrolyte to the catalyst surface and the impact of an electrical polarization on the catalytic activity, several light-off experiments (cool down and heat up procedures) were successively performed under different polarizations, i.e. OCV, +2 and −2 V. These experiments have clearly shown that the presence of O²⁻ (thermally or electrochemically induced) inhibits the catalytic activity of the platinum for the propene deep oxidation. These results demonstrate the importance to define a normalized rate enhancement ratio, ρ _n , from a reference value of the catalytic rate corresponding to a Pt surface state free of O²⁻ ions.     

Impacts of varnishes and impregnation chemicals on combustion properties of oak (Quercus petreae lipsky)

This study was performed to determine the effects of varnishing after impregnation with boron compounds on combustion properties of oak. For this aim, the test samples prepared from oak (Quercus petreae Liebl.) wood were impregnated according to ASTM D 1413‐99 with boric acid (Ba) and borax (Bx) by vacuum technique. After impregnation, surfaces were coated by cellulosic (Cv), synthetic (Sn), polyurethane (Pu), waterborne (Wb), acrylic (Ac), and acid hardening (Ah) varnishes in accordance to ASTM D 3023. Combustion properties of samples after varnishing process were determined, according to ASTM E 160‐50. According to material and process types, combustion temperature was the highest in Bx and Cv, the lowest in Ba and Ac. An important difference was not observed between without flame source combustion (WFSC) and flame source combustion (FSC). According to combustion type, impregnation material and varnish type, combustion temperature was the highest value in WFSC + Bx + acid hardening varnish combination and the lowest in WFSC + Ba + acrylic varnish combination. As a result, the tested varnishes showed an increasing impact but boron compounds showed a decreasing impact on combustion properties of oak. In consequence, for usage areas having a high risk of fire, impregnation of wood material with boron compounds before varnishing will decrease combustion temperature and provide security. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

白云鄂博主矿开拓运输工艺转换有关问题的探讨

本文对白云鄂博主矿采场铁公路联合运输向公路运输转换位置是否确定为1638m水平以及运输工艺转换过程中相关问题进行分析论证，提出主矿采场铁路至少可向下延深一个水平，技术上可行，节约运费千万元以上。     

Pulsating Jet Impingement Heat Transfer Enhancement

This article presents results from a numerical study of pulsating jet impingement heat transfer. The motivation is to seek conditions offering a significant enhancement compared to steady flow impingement drying. The CFD software package FLUENT was used for simulating slot-type pulsating jet impingement flows with confinement. The parameter study included velocity amplitude ratio, mean jet velocity, and pulsation frequency. The distance from nozzle exit to surface was three times the hydraulic diameter of the nozzle. The Reynolds number based on the nozzle hydraulic diameter and jet temperature was 2,460 with a mean jet velocity of 30 m/s, which is the base case of the numerical experiments. Results showed that time-averaged surface heat transfer increased with increasing velocity amplitude for the same mean jet velocity. Large velocity amplitudes helped enhance heat transfer by two mechanisms: high jet velocity during the positive cycle and strong recirculating flows during the negative cycle. For the cases with different mean jet velocities but the same maximum velocity, time-averaged surface heat flux decreased with decreasing mean jet velocity. As for the effects of pulsation frequency, with high-velocity amplitude ratio, time-averaged surface heat fluxes were at the same level regardless of frequency. However, at low-velocity amplitude ratio, high frequency caused stronger recirculating flows resulting in greater heat transfer compared to the cases with a lower frequency.     

Characterization of Thai limestone for desulphurization in a fluidized bed combustor

The objective of this study is to determine the chemical kinetics of desulphurization of Thai limestone in an atmospheric fluidized bed combustor (AFBC). The experiments, which employed the batch technique using the limestone samples from six major sources in Thailand, were performed in a laboratory‐scale AFBC. The results obtained were analysed and correlated in the form of apparent reaction rate and deactivation rate constants as a function of operating conditions of the furnace and their properties, respectively. The formulae derived from these correlations were kept as general as possible in order that they could be used as input parameters for the selected mathematical model of desulphurization in an AFBC that is suitable for practical use. The predicted results were in good agreement with the experimental data reported in the literature. Copyright © 2003 John Wiley & Sons, Ltd.     

国产50%离子膜法烧碱蒸发装置及运行情况

介绍了升降膜法双效逆流蒸发生产50%离子膜法烧碱的工艺流程、主要设备、装置特点及运行情况.     

Synthesis of silicon oxynitride by infiltration-mediated combustion

Silicon oxynitride Si₂N₂ O was synthesized from a mixture of Si, SiO₂, and Si₃N₄ by infiltrationmediated combustion in nitrogen gas. The chemical/phase composition of product and process parameters (temperature and burning velocity) were studied upon variation in charge composition and initial pressure of gas reagent. Parameters of the reaction yielding single-phase Si₂N₂O have been optimized.      

Ergodicity of filtering process by vanishing discount approach

A new approach to study ergodicity of filtering processes is presented. It is based on the vanishing discount approach to discounted functional of filtering process. We show that limit superior of the Cesaro averages of the functionals is the same for all initial conditions from which the uniqueness of invariant measures of filtering processes follows. The approach is based on certain assumption for which we provide a sufficient condition using concavity arguments. In addition we show the existence of solutions to the Poisson equation corresponding to filtering process with concave functional. The assumptions are then extended to the controlled case and using similar concave arguments we obtain the existence of solutions to the Bellman equation corresponding to partially observed average cost per unit time problem.