PAN/FPU Composite Nanofiber Membrane with Superhydrophobic and Superoleophobic Surface as a Filter Element for High-Efficiency Protective Masks

Recently, because of the outbreak of COVID-19, the demand for various types of filter elements in protective materials has increased globally. Furthermore, new requirements for the filtration performance of PM2.5 liquid (oil) particles have been put forward. In this work, Superhydrophobic and superoleophobic composite nanofibers with excellent filtration capacity for oil and salt particles are developed through the modification of polyacrylonitrile (PAN) by fluoro-polyurethane (FPU) doping. The results show that the PAN/FPU composite nanofibers doped with 9 wt% FPU has a uniform fiber morphology with a diameter of 240 ± 30 nm. Compared to the pure PAN nanofibers, the water-based contact angle of PAN/FPU increases from 90 ± 5° to 151 ± 5°, and the oil-based contact angle increases from 58 ± 2° to 152 ± 3°. Importantly, at a high flow rate of 95 L min⁻¹, the filtration efficiency of the PAN/FPU nanofiber membrane for 0.3 µm oil particles increases from 92 ± 1% to 99.2 ± 0.1%. After cyclic loading, the filtration efficiency of 0.3 µm oil particles remains above 98%. Meanwhile, the filtration efficiency for 0.3 µm salt particles remains at 98.23 ± 0.1%. The PAN/FPU nanofiber membrane developed in this work is effective in applications and has good market prospects as a protective filtration material.     

浅议降低脉冲袋式除尘器运行费用的几点措施

脉冲袋式除尘器,因其具有良好的清灰效果,并可在较高的过滤风速下稳定运行,因而在袋式除尘器中,占有极其重要的地位。本文介绍了如何降低脉冲袋式除尘器的运行费用,并提出了相应的措施及其在设计中应注意的问题。     

空压机叶片腐蚀分析

空压机第三级叶轮的叶片严重腐蚀，经光谱、能谱及X射线分析，结果表明光叶腐蚀是因进入空压机的空气中含有大量SO2有害气体和第二级中间冷却器放水器排水不正常，使第三级叶片处于含硫的酸性气氛中而引起的。     

热管空冷器在淬火介质控温过程中的应用

针对连续淬火介质在工作中存在的冷却问题，提出由空气冷却代替水冷系统，研制出的热管空冷器可以精确控制连续淬火介质温度，保证热处理工件的金相组织和力学性能，在实际应用中取得较大成效。     

用于气体保护焊的自动混气设备

介绍了一种用于焊接现场的气体保护焊的自动混气设备，该设备能精确控制气体混合比例。设备主要由气体传输、气体混合、信号检测和电气控制几大部分组成。计算机适时采集、显示混合气体的混合比例、输出压力、气体湿度等信息，超限发出声光报警。混气设备通过气体分析仪、比例阀和计算机形成闭环控制，从而实现气体混合比例的精确控制。     

燃气加热托辊型网带炉生产线的研制与应用

介绍了燃气加热托辊型网带炉生产线的组成、燃气脉冲控制和空气/燃气比例连续调节技术和计算机多媒体集散控制系统.生产应用表明炉温均匀性良好,处理产品质量稳定,能耗成本降低,取得了明显的经济效益.     

用气冲气推成形触头造型机制造电机壳铸型的试验研究

扼要介绍了用气冲气推成形触头造型机制造电机壳铸型的成型过程及其实砂效果,试验结果表明,在工作气压为0,4￣0.45MPa的条件下,气冲气推成形触头造型机对电机壳类铸型的紧实,实砂效果十分理想,砂型紧实度高而且均匀。     

浅谈出口巴基斯坦铁路客车新型酚醛玻璃钢风道的研制开发

本文阐述了新型酚醛玻璃钢风道的成型工艺、开发过程，并与传统玻璃钢风道作了比较，论述了新型酚醛玻璃钢风道的优点，并对其应用前景和对铁路客车的设计思路的影响进行了探讨。     

用直接纺丝法制芳纶短纤维

研究了直接纺丝制取芳纶短纤维的新方法。讨论了纤维长度、直径及力学性能与纺丝条件的关系。发现影响纤维长度的主要因素是空气层高度和喷丝速度,影响纤维直径的主要因素为喷口直径及喷丝速度。此外,还用PPTA短纤维制成了均匀的PPTA"浆粕"纤维。     

Comparison of a contactor catalytic membrane reactor with a conventional reactor: example of wet air oxidation

A wet air oxidation reaction was carried out in a gas/liquid catalytic membrane reactor of the contactor type. The oxidation of formic acid was used as a model reaction. The mesoporous top-layer of a ceramic tubular membrane was used as catalyst (Pt) support, and was placed at the interface of the gas (air) and liquid (HCOOH solution) phases.

A similar reaction was carried out in a conventional batch reactor, using a steering rate high enough to avoid gas-diffusion limitations, and exactly identical conditions than for the CMR (amount of catalyst, pressure, etc.). At room temperature, the CMR showed an initial activity three to six times higher than the conventional reactor. This activity increase was attributed to an easier oxygen access to the catalytic sites. Nevertheless, the catalytic membrane gradually deactivated after a few hours of operation. Different deactivation mechanisms are presented.