Determining the life cycle of bolts using a local approach and the Dang Van criterion

The fatigue behaviour of bolts under axial load has always been considered from the component point of view for which fatigue limit is usually taken equal to 50 MPa, and few results are available to designers for limited lifetimes. Here, we take up this problem from a material point of view using a local approach. For each case of fatigue testing, using finite‐element (FE) model of the bolt, we determine the stabilized local stress at the root of the first thread in contact with the nut. To characterize bolt behaviour with these numerical results, we use Dang Van multiaxial fatigue criterion for which we extend application to the medium fatigue life. These results can be correlated with the experimental numbers of cycles to failure to determine material parameters of the generalized criterion. Using statistical Gauss method, we can make lifetime predictions for any level of risk of failure. In addition, we propose an analytical model to rapidly determine the local stress condition from nominal loading data (mean stress and alternating stress). This model dispenses us from a new modelling if the bolt is stressed in the same manner as the bolts used for behaviour characterization. Using this model and the generalized criterion, it is extremely easy to make lifetime predictions whatever the risk considered.     

Comparative study of the electrical properties of diamond films grown by microwave plasma assisted and hot-filament chemical vapor deposition

Schottky diodes were built on different polycrystalline diamond films grown by Microwave Plasma and Hot Filament Chemical Vapor Deposition and their electrical properties were studied. The barrier height increased with the diamond film quality and the corresponding ideality factor decreased. Even though the lower-quality HFCVD film displayed poor rectifying properties, it was found to be much less sensitive to variations in the operating conditions (air vs. vacuum). The activation energies of the films depend on morphological parameters, as preferable grain size or orientation. The bulk conduction also depends on the quality of the deposited films, changing from ohmic to trap-free or shallow trap SCLC and SCLC with an exponential distribution of traps. The hypothesis of using the electrical measurements as an indicator for film quality has been discussed.     

Critical incidents and chronic stressors at work: Their impact on forensic doctors.

Workers in medium- or high-risk professions are often confronted with critical incidents at the workplace. The impact of these acute stressors may be serious and enduring. Many workers also experience chronic job stressors, such as work overload or role conflicts. This study examined the frequently neglected relationship of acute and chronic stressors with self-reported health symptoms, such as posttraumatic responses, fatigue, and burnout. This association was investigated in a sample of forensic doctors in the Netherlands (N = 84). It was found that the more traumatic events the respondents experienced, the more problems they reported in coping with the traumatic events. Chronic job stressors were associated with posttraumatic responses (intrusions and avoidances) and with burnout and fatigue. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Finite element simulation of the mechanics of flat contact pad fretting fatigue tests

An understanding into the macro kinetic and kinematic behaviour of fretted surfaces is provided. Making use of a modified version of a previously developed in‐house two‐dimensional elastic–plastic finite element analysis numerically simulates flat contact pad fretting fatigue tests. Basic macro mechanics concepts are adopted to idealise two bodies with rough contact surfaces and loaded at two different sites with arbitrary axial loading profiles. A time scale factor is devised to recognise the earliest candidate out of the events possibly accommodated at each loading increment. The present analysis utilises a relevant experimental set up developed in the Structural Integrity Research Institute of the University of Sheffield as an application. Computational results accurate to within 1.2% and corresponding to one contact pad span and six constant normal loads acting individually with four amplitudes of two sinusoidal axial load cycles are presented. The present computations include (1) the development of the global and local normal and tangential reactions and relative sliding displacement acting along the fretting surfaces and (2) contact pad deformation, generated stress fields and plasticity development within the neighbouring region of the fretted area.     

Effects of chemical and plasma surface treatments on the O2-annealed Ni/Au contact to p-Gan

The effects of boiling Aqua Regia (AQ), N₂/Cl₂ plasma followed by AQ and O₂ plasma followed by AQ surface treatments prior to Ni/Au (20 nm/20 nm) metallization to p-GaN:Mg (∼ 3 × 10¹⁷ cm^− 3) have been investigated. N₂/Cl₂ plasma was employed in a bid to lower the Ga/N and O/Ga ratios of the GaN surface to improve the contact properties to p-GaN, while O₂ plasma was employed as an alternative to incorporate O into the Ni/Au system. Results show that a low Ga/N ratio does not necessarily correspond to a better contact. The positive effect of O₂ over N₂ anneal is observed only for the AQ-treated sample, although the mechanisms responsible for its positive effect: NiO formation and Ni/Au layer-reversal were observed for all O₂-annealed contacts. We conclude that the effect of O₂ anneal on the Ni/Au contact is dependant on the p-GaN surface prior to metallization.     

Effect of Rare Earth Elements on Thermal Fatigue Property of Low Chromium Semi-Steel

The effect of rare earth elements on eutectic carbide‘s morphology of low chromium semi-steel in as-cast state and after heat treatment was investigated, and accordingly, the thermal fatigue property of this material was studied. The results show that RE can improve the eutectic carbide‘s morphology, inhibit the formation and propagation of thermal fatigue cracks, therefore, promote the thermal fatigue property, which is more noticeable in case of the RE modification in combination with heat treatment. The optimal thermal fatigue property can be obtained when treated with 0.2% RE modification as well as normalization at 950℃ for 3h.     

LOW-CYCLE FATIGUE UNDER NON-PROPORTIONAL LOADING

A series of strain-controlled, low-cycle fatigue experiments have been conducted on 42CrMo steel under various loading paths including circular, square, cruciform, and rectangular paths. Present experiments have shown that there is additional hardening under non-proportional cyclic loading. Non-proportional cyclic additional hardening also results in a shorter life for multiaxial low cycle fatigue. A non-proportionality measure of strain path based on both a physical basis and macromechanical phenomena is proposed. The loading path effect on additional hardening is also described well. Low-cycle fatigue damage accumulation and the evolution process under non-proportional loading is analysed via the Continuum Damage Mechanics Model of Chaboche. A non-proportinality measure is introduced in the damage evolution equation and a modified Coffin-Manson type formula is derived. A novel fatigue life prediction approach based on the critical-plane concept of Brown and Miller is proposed.     

THE EFFECT OF CATHODIC PROTECTION POTENTIAL ON CORROSION FATIGUE CRACK GROWTH RATE OF AN OFFSHORE STRUCTURAL STEEL

Abstract— Duplicate tests have been performed to determine the effect of cathodic protection potential on corrosion fatigue crack growth rate of a modern offshore structural steel, produced by thermo-mechanically controlled processes. The experiments were carried out using compact tension specimens exposed to artificial seawater at 10°C and subjected to constant amplitude loading at 0.35 Hz. Reproducible results showed that the merits of cathodic protection potentials are strongly dependent on stress intensity ratio R and stress intensity range Δ K . It appears that a specific value of cathodic potential may not give comprehensive protection against corrosion fatigue within the spectrum of variable amplitude loading experienced in service. Fractography showed the initiation of secondary cracks on the fracture surface to be associated with the dissolution of calcium sulphide inclusions, regardless of imposed cathodic potential.     

Contact interaction of double titanium and chromium diboride with Fe-Cr alloys

The kinetics of wetting double titanium and chromium diboride by iron-based alloys with different chromium content is studied. It is shown that contact angles are formed in such systems over the range 0–10°. The energy parameters of wetting are calculated. It is established that chromium as a surface-active element promotes Fe-Cr alloy spreading on the diboride surface. The microstructure of the interaction area is studied. It is shown that terminal solid solutions and eutectics are formed in the TiCrB₂-(Fe-Cr) system. The optimum compositions of the metallic binder are determined for TiCrB₂-based composite materials. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 1–2(453), pp. 109–115, 2007     

矫直辊与板材的接触点位置对矫直过程影响的研究

介绍了辊式矫直过程中，板材与矫直辊的接触点位置对矫直过程的影响，以及接触点对矫直过程影响的一系列研究，最后对接触点在矫直过程中的分析方法及作用进行了预测。