Finite elements in the analysis of pressure vessels and piping-a bibliography (1976–1996)

The paper gives a bibliographical review of the finite element methods (FEMs) applied for the analysis of pressure vessel structures/components and piping from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore the aim of this review is to give the reader an encyclopaedic view of the differnt possibilities that exist today for the finite element analysis in the fields of pressure vessels and piping. The bibliography at the end of the paper contains approximately 1900 references to papers, conference proceedings and theses/dissertations on the subject that were published in 1976–1996. These are classified in the following categories: linear and non-linear, static and dynamic, stress and deflection analysis; stability problems; thermal problems; fracture mechanics problems; contact problems; fluid-structure interaction problems; manufacturing of pipes and tubes; welded pipes and pressure vessel components; development of special finite elements for pressure vessels and pipes; finite element software; and other topics. Also finite element software, general purpose and special purpose codes, used for the analysis of pressure vessels and pipes are briefly discussed and presented.     

A BOUNDARY INTEGRAL EQUATION AND ITS NUMERICAL SOLUTION OF POTENTIAL FLOW AROUND SURFACE-IRREGULA-RITIES

In this paper,using complex functional theory,the authors turn the potentialflow around the surface irregularities in a pressure conduit and semi-infinite platforms intoDirichlet problem.Based on Schwarz formula and by the application of Plemelj's formula,theauthors change the problem into the integration of a Cauchy boundary integral equation in theflow plane through the substitution of variables.Using numerical integration,the authors obtainthe velocity distribution and pressure coefficient along surface irregularities and platforms.Thephysical concept of this method is clear,the convergent speed is rapid and the computative effi-ciency is high.The calculated values agree well with the measured results.It is an effective andsimple method in solving potential flow.     

The effect of pre-wetting on dynamic contact angles

A roll-coating experimental system is used to study the effect of pre-wetting on dynamic contact angles, the interfacial displacement depth, and the associated phenomenon of air entrainment. The system consists of a roll, which is horizontally rotating in a liquid pool. The dynamic contact angle is recorded by a macrophotography system. The test liquids are glycerol solutions with viscosities in the range 104 < μ < 748 mPa · s. The value of (μV/ρg)^0.5 is taken as the characteristic length to be used in the dimensionless relationships which correlate experimental measurements. The effect of base layer entry angle into the liquid pool on the dynamic contact angles and other flow parameters is studied. Comparison is made with measurements in dry tape-coating and other pre-wet roll–coating systems.     

Pad effects on material-removal rate in chemical-mechanical planarization

The role of a porous pad in controlling material-removal rate (MRR) during the chemical-mechanical planarization (CMP) process has been studied numerically. The numerical results are used to develop a phenomenological model that correlates the forces on each individual abrasive particle to the applied nominal pressure. The model provides a physical explanation for the experimentally observed domains of pressure-dependent MRR, where the pad deformation controls the load sharing between active-abrasive particles and direct pad-wafer contact. The predicted correlations between MRR and slurry characteristics, i.e., particle size and concentration, are in agreement with experimentally measured trends reported by Ouma¹ and Izumitani.²     

环境因素对碳钢点蚀临界电势的影响

采用动电势扫描法测定了不同体系中碳钢发生点蚀的临界电势Eb。结果表明 :当Cl- 浓度 <0 .0 1mol/L时 ,随Cl- 浓度增加 ,临界电势负移并与Cl- 浓度成线性关系 ;pH值在 7～ 11之间 ,随pH值增加 ,临界电势正移并与pH值成线性关系 ;随温度增加 ,临界电势负移并与温度成线性关系。     

ˮ�ཬ������������Ƽ�����Ľ�������о�

解决注水泥作业的防气窜问题，是提高固井质量，保护油气层的关键技术。现有预测和防止水泥浆气管理的方法虽然较多，但应用于现场却有一定困难，主要表现在所考虑的因素比较单一，有些高温、高压下的水泥浆性能参数难以测定。文章在分析国内外预测和防止气窜方法的基础上，应用水泥浆浆体在环空的组成，GFP系数、水泥浆稠度阻力系数（A）及多凝水泥和环空加压等措施，拟定出一套提高水泥浆顶替效率，保证水泥浆动态和静态过程压力平衡关系的具体设计方法。     

轴对称问题线元上分布奇点的诱导速度势和诱导速度

本文给出轴对称问题线元上高次分布源和偶极在无界域中的诱导速度势和诱导速度的计算公式,可供用分布奇点法求解轴对称势流问题时参考.     

Machining with tool–chip contact on the tool secondary rake face—Part II: analysis and discussion

The forces, chip thickness, and natural tool–chip contact length in machining with a double-rake-angled tool are predicted in Part II of the present study. It is revealed that in comparison with a single-rake-angled tool, a double-rake-angled tool increases the forces, especially the thrust force. However, the increase in chip thickness and tool–chip contact length is not significant under the input conditions specified in the present study. The effect of seven input variables of the proposed model is quantitatively investigated. The predicted variations of forces, chip thickness, and natural tool–chip contact length are in good agreement with theoretical and experimental results obtained by other researchers. The interrelationships among the resultant force, the chip thickness, and the natural tool–chip contact length are established, which provides a new and promising method to estimate the tool–chip contact length by employing the resultant force. It is demonstrated that the model can also be extended to study the problem of machining with a groove-type chip breaker tool.     

T8钢—聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性，磨料磨损性及土壤的减粘降组性能，与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％－－２２．２７％。     

Adhesive Contact of a Membrane with a Hemispherical Indenter: Theoretical Analysis and Model Liquid System

The axisymmetric Laplace equation is solved numerically to extract contact-angle data for a flat liquid/vapor interface contacting a submerged hemispherical solid. The liquid/vapor interface is treated as a membrane, with a membrane tension equal to the surface energy of the liquid. By measuring the vertical displacement of the membrane and the projected contact area the membrane makes with the hemisphere, the contact angle and correspondingly the driving force for motion of the contact line can be measured. We show that characteristic receding and advancing contact angles can be obtained by measuring the contact radii formed upon initial contact between the interface and hemisphere and final contact just prior to detachment of the interface, respectively. Use of the technique is illustrated with a model experiment involving the contact of an air/water interface with a poly(methyl methacrylate) surface.