钻进过程中金刚石钻头磨损规律试验研究

为了研究人造金刚石孕镶钻头(以下简称钻头)磨损规律，采用均质人造岩石(瓷砖)进行钻进试验，并在试验过程中采用对钻头唇面进行连续显微照相和将钻头称重的方法，获得以下三点结论：(1)在钻进过程中，钻头唇面上出露出的金刚石量呈周期性变化，每变化一个周期钻头就换一层新的金刚石；(2)钻头的钻速随钻头唇面出露金刚石量而变化，金刚石出露多，钻头钻速高，反之亦然；(3)钻头磨损速度随钻头钻速的变化而变化，钻头钻速高，钻头磨损速度快，反之亦然。     

基于FPGA的硬圆弧插补器设计

基于PC的数控系统成为开放式数控系统发展的必然趋势，其中PC加控制板卡的结构为实际的开放式标准体系。本文采用FPGA器件实现了扩展DDA圆弧插补算法，在满足较高精度的情况下，具有较快的插补速度，而且容易与电机的运动控制部分很好的信成，制作成控制板卡，从而适应目前基于PC加控制板卡的开放式数控系统的发展趋势。     

叶蜡石的矿物成分对合成金刚石的影响

通过对闽东矿区五种不同类型叶蜡石所做的化学分析及DTA、TG分析，计算出了其相应的矿物成分。将这几种叶蜡石分别制成传压介质进行了合成金刚石的实验并与北京门头沟叶蜡石作了比较，结果表明：(1)含有一定量石英(20％左右)的叶蜡石做传压介质有利于降低金刚石合成压力，提高金刚石质量；(2)结晶水含量较低的叶蜡石合成出的金刚石质量更好。作者对实验结果进行了分析并指出：在选择作为传压介质的叶蜡石时，不能只要求其硬度低、叶蜡石成分高，而应全面考虑其中所含矿物成分及其在高温高压下可能发生的变化。     

金刚石颗粒在锯切石材过程中磨损形态的研究

本文分析和归纳了锯切花岗石过程中金刚石颗粒的五种磨损形态和三个磨损阶段，探讨了金铡石颗粒磨损形态对金刚石锯片锯切性能的影响。     

Surface Pretreatments of Silicon Nitride for CVD Diamond Deposition

The efficiency of different surface pretreatments (four standard chemical etchings and four diamond powder abrasive procedures) on silicon nitride (Si₃N₄) substrates for chemical vapor deposition (CVD) of diamond has been systematically investigated. Blank Si₃N₄ samples were polished with colloidal silica (∼0.25 μm). Diamond nucleation and growth runs were conducted in a microwave plasma chemical vapor deposition apparatus for 10 min and 6 h, respectively. Superior results concerning nucleation density ( N _d∼ 10¹⁰ cm⁻² after 10 min), film uniformity, and grain size (below 2 μm after 6 h) were obtained for the mechanically microflawed samples, revealing that chemical etchings (hot and cold strong acids, molten base or CF₄ plasma) are not crucial for good CVD diamond quality on Si₃N₄.     

Electrochemical characteristics for redox systems at nano-honeycomb diamond

Electrochemical characteristics for several redox systems at diamond films with highly ordered nanometer-scale cylindrical pores (‘nano-honeycombs’) were examined with cyclic voltammetry (CV) and electrochemical impedance measurements. The cyclic voltammetric anodic-cathodic peak separations for these nano-honeycomb electrodes were in the same range as those for polished polycrystalline diamond films, indicating that the involvement of the oxygen-terminated surface of the nano-pore walls, which should give rise to large peak separations for certain redox couples was only slight. Moreover, the peak currents in the CV were not enhanced to the extent expected on the basis of the roughness factors of the nano-honeycomb films. Ac impedance plots results indicated the existence of a concentration gradient of the reactant in the nano-pores, which is in agreement with theoretical predictions for charge transfer reactions in porous electrodes. The average concentration of the reactant (Fe^2+/3+) inside the nano-pores was a factor of ca. 80 lower than that in the bulk electrolyte. The results of the impedance analysis also indicated an increase in the reaction resistances with decreasing pore diameters.     

DECOUPLER DESIGN AND CONTROL SYSTEM TUNING BY INA FOR DISTILLATION COMPOSITION CONTROL†

Six distillation column models have been used in studies of the usefulness of the Inverse Nyquist Array (INA) method for design of dual composition control for distillation. Five of the column models are experimental, one describing an industrial column, the others four pilot plants. One column model is obtained by modeling from first principles.

The control strategies investigated and compared are multiloop SISO, 2-way decoupling and l-way decoupling. The control variables are the standard ones, i.e. reflux flow and boilup.

In most of the cases INA has been found to be a useful tool for design of the loops and for comparison of the different control approaches. INA has also been found to be useful for simultaneous tuning of the decouplers and the feedback controllers.

For 2-way decoupling the criterion to minimize interaction at the critical frequency for each primary feedback loop has been found useful in most, but not all, cases. The scheme can be designed by pure gains in the decouplers and there is no reason to introduce dynamics into the decouplers—the systems studied are already sufficiently rich in dynamics.

INA has been found to be a suitable vehicle for the choice between the two possible l-way decoupling schemes.

With the design approach taken, l-way decoupling has been found to provide considerably better control quality than 2-way decoupling in two of the six systems, the differences in control quality being small in the other cases.

The effect of model mismatching on the results, caused e.g. by process nonlinearities, is discussed and simple rules to decrease the parameter sensitivity for 2-way decoupling schemes are given. When model mismatching is considered, the advantage of l-way decoupling over 2-way decoupling seems to increase.

One deficiency of the INA design as used in this paper is that it does not single out the design which is to be preferred on the grounds of robustness.     

Band Gap Modification of Diamond Photonic Crystals by Changing the Volume Fraction of the Dielectric Lattice

Photonic crystals with a diamond structure of epoxy lattices in which TiO₂-based ceramic particles are dispersed were fabricated by stereolithography. The periodicity of the lattice was designed to reflect electromagnetic waves in the gigahertz range. The volume fraction (β) of the dielectric lattice medium was modified from 14% to 33% by changing the rod diameter of the lattice. The photonic band gap was observed along Γ-L 〈111〉, Γ-X 〈100〉, and Γ-K 〈110〉 directions and the complete photonic band gap was formed at over β= 20%. The width of the forbidden gap increased gradually when the β increased over 14%, and reached 2.4 GHz at β= 33%. These results agreed with the band calculation using the plane wave expansion method.     

六面顶金刚石压机液压系统压力及超高压优化控制

针对六面顶人造金刚石压机的复杂生产流程要求,设计开发了六面顶人造金刚石压机液压系统的计算机控制装置.其中液压系统压力控制部分采用外置模拟式PI调节器,可根据生产工序的要求自动优化控制器设定值;超高压控制部分采用智能预测与纯比例控制相结合的控制策略,明显提高了人造金刚石压机的液压控制精度.该控制装置已投入实际运行,在改善产品质量品级方面取得了显著的经济效益.     

相控阵雷达天线阵面记录回放系统

相控阵雷达广泛应用,其天线阵面对记录回放系统的数据速率要求提升。针对两种传统记录回放系统架构的不足,结合其优点,设计并实现了一种新型的基于FPGA的记录回放系统。该系统设计为板卡的形式,FPGA实现对硬盘的读写操作,采用自定义的文件系统对数据进行管理。经过测试,系统记录速度可以达到292 MB/s,回放速率为340 MB/s。实验结果表明,该记录回放系统性能稳定,通用性好,存储速率满足要求。